Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR(for 3 Door) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248329 REAR AIRBAG SENSOR(for 3 Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR(for 3 Door)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 3.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 4.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 5.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 81250 8.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 09113 9.REMOVE JACK HANDLE (for RH Side)

Hide 62313D 12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 73201C 13.REMOVE FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY

Hide 62510P 14.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY

Hide 73360 15.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

Hide 64730B 16.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 64740C 17.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

Hide 89860B 18.REMOVE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B282661

Disconnect the connector from the No. 2 side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push and hold the white housing lock, and slide the outer connector locking sleeve.

C195226E24
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 false 1.135,0.99 1.135,0.531 1.135,0.531 1.052,0.531 true 3.656,1 3.656,0.542 3.656,0.542 3.573,0.542 true 0.875,1.729 1.063,1.896 0.188,0.167 10 false *a 3.417,1.75 3.813,1.958 0.396,0.208 10 false *a 0.906,0.458 1.094,0.635 0.188,0.177 10 false *1 3.417,0.469 3.604,0.646 0.188,0.177 10 false *1 1.302,2.156 1.49,2.333 0.188,0.177 10 false *2 3.854,2.156 4.042,2.333 0.188,0.177 10 false *2

Text in Illustration
*1 Housing Lock *2 Outer Connector Locking Sleeve
*a Slide - -


ii.

Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.



d.
B282662

Remove the bolt and No. 2 side airbag sensor assembly.

NOTICE:

Loosen the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly pin (stopper) is easily damaged.