Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)
RM19S0E _58 Vehicle Interior _051497 SEAT BELT _0248339 FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 73210 1.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B225046E03
1.905,0.148 2.297,0.387 0.392,0.239 10 45° 0.538,0.066 0.734,0.233 0.195,0.167 10 *a 2.52,1.126 2.706,1.288 0.186,0.162 10 *b

Check the angle of inclination required to lock the retractor.

i.

Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15 ° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45 ° or more.

Text in Illustration
*a Unlock
*b Lock

NOTICE:

Do not disassemble the retractor.


If the operation is not as specified, replace the front seat outer belt assembly.



b.
U134348E01
1.283,0.626 1.410,0.787 0.127,0.160 10 A 2.142,2.534 2.269,2.695 0.127,0.160 10 B

Engage the 2 hooks and temporarily install the front seat outer belt assembly with the 2 bolts.


c.

Tighten bolt A and then bolt B.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)

for bolt A

42 N*m (428 kgf*cm, 31 ft.*lbf)

for bolt B



d.
B282675E01
0.999,2.782 1.227,2.593 false 1.24,2.5 1.459,2.682 0.219,0.182 10 *1

Connect the pretensioner connector.

Text in Illustration
*1 Locking Button


e.

Lock the locking button.

NOTICE:

Securely lock the locking button.



f.

Install the shoulder anchor part of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.

Check that the ELR locks.

NOTICE:

The check should be performed with the front seat outer belt installed.


i.

With the belt installed, check that the belt locks when it is pulled out quickly.

NOTICE:

If the operation is not as specified, replace the front seat outer belt assembly.




i.

Remove the 2 bolts and the front seat belt outer bar sub-assembly, disconnect the floor anchor part of the front seat outer belt assembly .


Hide 73201C 4.INSTALL FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY

a.

Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62311B 5.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 7.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 8.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 9.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)