Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.06
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248351 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1451  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor with pulley assembly receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor with pulley assembly changes the amount of compressor output.

DTC No. DTC Detection Condition Trouble Area
B1451 An open or short in the cooler compressor solenoid circuit.
·

Compressor with pulley assembly

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E227902E01
2.42,0.647 2.527,0.816 0.107,0.170 10 2 2.42,1.218 2.515,1.375 0.095,0.158 10 1 4.456,0.647 4.640,0.816 0.184,0.170 10 11 4.724,0.741 5.123,0.897 0.399,0.156 10 SOL+ 4.255,1.694 4.512,1.839 0.257,0.145 10 F41 4.262,1.841 6.508,2.004 2.246,0.163 10 Air Conditioning Amplifier Assembly 0.633,1.694 0.900,1.843 0.267,0.149 10 B77 0.633,1.864 2.795,2.018 2.162,0.154 10 Compressor with Pulley Assembly 1.936,0.741 2.335,0.897 0.399,0.156 10 SOL+ 1.936,1.309 2.335,1.465 0.399,0.156 10 SOL-

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Regulator Control Current Regulator control current /
Min.: 0 A
Max.: 0.997 A
Value changes between 0.12 A and 0.997 A in accordance with compressor operation -

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.INSPECT COMPRESSOR WITH PULLEY ASSEMBLY
3.INSPECT COMPRESSOR WITH PULLEY ASSEMBLY
a.

Inspect the compressor with pulley assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1NZ-FE, 2NZ-FE)>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the B77 compressor with pulley assembly connector.


b.

Disconnect the F41 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-2 (SOL+) - F41-11 (SOL+) Always Below 1 Ω
B77-2 (SOL+) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH PULLEY ASSEMBLY - BODY GROUND)
a.
U158520E01
0.511,0.898 0.775,1.079 0.264,0.181 10 B77 0.047,0.024 0.217,0.184 0.170,0.161 10 *a 0.56,1.575 0.948,1.731 0.387,0.156 10 SOL- 1.491,1.265 1.036,1.668 false

Disconnect the B77 compressor with pulley assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-1 (SOL-) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Pulley Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR