Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › 2014.07–2017.01
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248385 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.
B106929

Using a scraper, remove the adhesive sticking to the back door glass.

NOTICE:

Be careful not to damage the back door glass.



b.

Clean the outer edge of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Even if using a new glass, clean the glass with non-residue solvent.




Hide 64827B 2.INSTALL BACK WINDOW GLASS CLIP RH

a.

Apply Primer G to the installation part of the back window glass clip.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.




b.
B272674E01
0.125,0.093 0.307,0.257 0.182,0.164 10 *a

Install a new clip onto the glass, as shown in the illustration.

Text in Illustration
*a Back Side


Hide 64828B 3.INSTALL BACK WINDOW GLASS CLIP LH

a.

Apply Primer G to the installation part of the back window glass clip.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.




b.
B272675E01
0.1,0.051 0.280,0.221 0.180,0.170 10 *a

Install a new clip onto the glass, as shown in the illustration.

Text in Illustration
*a Back Side


Hide 64813B 4.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of adhesive dam with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.




b.

Install a new adhesive dam onto the back door glass, as shown in the illustration.

B272676E02
0.144,0.161 0.335,0.343 0.191,0.182 10 *a 2.625,0.689 2.757,0.841 0.132,0.152 10 A 2.625,1.035 2.757,1.187 0.132,0.152 10 A 2.002,1.895 2.135,2.047 0.132,0.152 10 B 2.002,2.239 2.135,2.392 0.132,0.152 10 B 4.697,0.728 5.362,0.881 0.665,0.152 10 A-A, B-B 5.579,1.055 5.753,1.208 0.174,0.152 10 *b

Text in Illustration
*a Back Side *b 6.9 mm (0.273 in.)


Hide 68131 5.INSTALL BACK DOOR GLASS

a.
B153152E01
0.249,0.812 0.418,0.967 0.169,0.155 10 *1 0.437,0.982 0.592,1.191 false 2.123,0.891 2.292,1.046 0.169,0.155 10 *1 2.311,1.062 2.457,1.298 false

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Adhesive

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.



b.
B272677E01
1.59,0.571 1.34,0.859 1.34,0.859 1.616,0.673 false 1.162,0.864 1.327,1.013 0.165,0.149 10 *a

Position the back door glass.

Text in Illustration
*a Mark

i.

Using suction cups, place the back door glass in the correct position.


ii.

Align the matchmarks on the back door glass and vehicle body.


iii.

Remove the back door glass.



c.
B271493E01
1.747,0.463 1.920,0.616 0.173,0.153 10 *1 1.769,1.515 1.942,1.667 0.173,0.153 10 *1 1.833,1.985 2.005,2.138 0.173,0.153 10 *2 3.009,0.488 3.182,0.640 0.173,0.153 10 *a 3.009,1.519 3.182,1.672 0.173,0.153 10 *b 1.94,0.586 2.276,0.861 false 1.962,1.634 2.272,1.8 false 2.025,2.051 2.228,1.918 false

Using a brush, coat the installation surface on the vehicle body with Primer M.

Text in Illustration
*1 Primer M
*2 Adhesive
*a Correct
*b Incorrect

NOTICE:
·

Do not coat the adhesive with Primer M.

·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Do not keep any of the opened Primer M for later use.




d.

Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

B292044E01
0.446,3.524 0.757,3.719 0.311,0.195 10 : *1 0.101,0.043 0.319,0.230 0.218,0.187 10 *a 2.738,1.46 2.910,1.644 0.172,0.184 10 A 2.738,1.109 2.910,1.293 0.172,0.184 10 A 2.097,2.664 2.269,2.848 0.172,0.184 10 B 2.097,2.313 2.269,2.497 0.172,0.184 10 B 0.643,1.185 0.815,1.368 0.172,0.184 10 C 0.974,1.3 1.146,1.484 0.172,0.184 10 C 4.89,2.066 5.255,2.238 0.365,0.172 10 C-C 4.89,0.561 5.517,0.733 0.627,0.172 10 A-A, B-B 5.934,0.755 6.164,0.936 0.230,0.181 10 *b 5.967,2.262 6.197,2.443 0.230,0.181 10 *c 5.71,2.961 5.940,3.141 0.230,0.181 10 *d

Text in Illustration
*1 Primer G - -
*a Back Side *b 14.0 mm (0.551 in.)
*c 22.0 mm (0.866 in.) *d 45.3 mm (1.783 in.)

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.




e.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B106205E08
2.395,0.851 2.579,1.020 0.184,0.170 10 *a 1.544,1.848 1.733,2.024 0.188,0.177 10 *b

Cut off the tip of the cartridge nozzle, as shown in the illustration.

Text in Illustration
*a 8.0 mm (0.315 in.)
*b 12.0 mm (0.472 in.)

HINT:

After cutting off the tip, use all adhesive within the time limit described in the table below.


Usage Time Frame:
Temperature Tack-free Time
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with a cartridge.



f.

Apply adhesive to the back door glass, as shown in the illustration.

B292045E01
0.449,3.54 0.771,3.715 0.322,0.175 10 : *1 0.11,0.059 0.314,0.234 0.204,0.175 10 *a 2.729,1.485 2.892,1.678 0.164,0.193 10 A 2.729,1.119 2.892,1.312 0.164,0.193 10 A 2.107,2.69 2.271,2.883 0.164,0.193 10 B 2.107,2.328 2.271,2.521 0.164,0.193 10 B 0.618,1.232 0.782,1.425 0.164,0.193 10 C 0.977,1.335 1.141,1.527 0.164,0.193 10 C 4.804,2.054 5.182,2.247 0.378,0.193 10 C-C 4.804,0.429 5.534,0.622 0.730,0.193 10 A-A, B-B 5.439,0.657 5.656,0.829 0.217,0.173 10 *b 5.973,1.113 6.190,1.286 0.217,0.173 10 *c 5.896,1.568 6.113,1.741 0.217,0.173 10 *d 5.407,2.299 5.624,2.471 0.217,0.173 10 *e 6.131,2.552 6.348,2.724 0.217,0.173 10 *c 5.907,3.06 6.123,3.233 0.217,0.173 10 *d

Text in Illustration
*1 Adhesive - -
*a Back Side *b 14.5 mm (0.571 in.)
*c 12.0 mm (0.472 in.) *d 8.0 mm (0.315 in.)
*e 52.3 mm (2.059 in.) - -


g.

Install the back door glass.

i.
B272677E01
1.59,0.571 1.34,0.859 1.34,0.859 1.616,0.673 false 1.162,0.864 1.327,1.013 0.165,0.149 10 *a

Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

Text in Illustration
*a Mark


ii.

Lightly press the front surface of the back door glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22 lb) or more.



iii.
B149738E08
2.921,1.148 2.921,1.463 false 0.71,0.129 0.898,0.280 0.188,0.151 10 *1 0.999,1.488 1.187,1.645 0.188,0.158 10 *2 0.018,0.826 0.187,0.977 0.169,0.151 10 *3 1.116,1.142 1.116,1.458 false 2.497,0.129 2.685,0.280 0.188,0.151 10 *1 2.817,1.481 3.005,1.638 0.188,0.158 10 *2 1.971,0.69 2.137,0.841 0.166,0.151 10 *3 0.206,0.939 0.502,1.124 false 0.799,0.295 0.799,0.837 false 2.599,0.312 2.599,0.838 false 2.145,0.856 2.417,1.148 false

If necessary, use a scraper to correct the level or position of adhesive that has been applied.

Text in Illustration
*1 Back Door Glass
*2 Dam
*3 Adhesive

HINT:

Apply adhesive onto the windshield glass rim.



iv.

Hold the back door glass using protective tape until applied adhesive hardens.

NOTICE:

Do not drive the vehicle within the time limits described in the table below.


Minimum time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




h.

Connect the 2 connectors.

HINT:

If the vehicle is equipped with rear window defogger, connect the connector.



Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 67894B 7.INSTALL BACK DOOR PANEL NO. 2 PROTECTOR

Hide 67893A 8.INSTALL BACK DOOR PANEL NO. 1 PROTECTOR

HINT:

Use the same procedure as for the No. 2 side.


Hide 85143R 9.INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 85110R 10.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 11.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 85292A 12.INSTALL REAR WIPER ARM HEAD CAP (w/ Rear Wiper)

Hide 67751 13.INSTALL BACK DOOR TRIM BOARD

Hide 76085 14.INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)