Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the engine is running or the ignition switch is ON, the power window regulator motor assembly LH or RH (driver side) is operated by the power window regulator master switch assembly. The power window regulator motor assembly LH or RH (driver side) has motor, regulator and ECU functions.

WIRING DIAGRAM

B291664E01
0.077,0.066 0.721,0.242 0.644,0.177 12 for LHD: 0.703,1.264 1.708,1.410 1.005,0.147 10 Main Body ECU 0.409,6.037 1.993,6.378 1.584,0.341 10 Power Window Regulator Master Switch Assembly 0.918,7.074 2.541,7.223 1.623,0.149 10 : LIN Communication Line 2.884,6.49 4.561,6.639 1.677,0.149 10 *1: w/ Rear Power Window 2.884,6.799 4.686,6.948 1.802,0.149 10 *2: w/o Rear Power Window 5.175,5.882 5.370,6.026 0.195,0.144 10 H3 5.175,6.044 6.768,6.552 1.593,0.508 10 Power Window Regulator Motor Assembly LH (Driver Side) 5.626,4.153 6.030,4.302 0.404,0.149 10 AUTO 5.626,3.541 6.097,3.683 0.471,0.142 10 DOWN 5.626,2.906 5.838,3.046 0.211,0.140 10 UP 5.332,2.82 5.504,2.966 0.172,0.147 10 10 5.407,3.432 5.505,3.579 0.098,0.147 10 7 5.423,4.07 5.524,4.212 0.100,0.142 10 4 1.083,3.536 1.552,3.688 0.468,0.151 10 DOWN 1.343,2.903 1.554,3.049 0.211,0.147 10 UP 1.133,4.149 1.552,4.306 0.419,0.157 10 AUTO 1.216,5.409 1.553,5.564 0.337,0.154 10 GND 1.638,2.185 2.237,2.335 0.599,0.150 10 6*1, 15*2 1.436,2.267 1.555,2.423 0.119,0.156 10 B 3.675,2.267 4.669,2.423 0.994,0.156 10 from P/W Relay 3.057,1.645 3.833,1.801 0.776,0.156 10 from Battery 4.353,1.794 4.800,1.931 0.448,0.137 10 DOOR 2.779,2.405 3.064,2.551 0.286,0.145 10 P/W 0.409,5.87 0.608,6.023 0.199,0.153 10 H1 5.402,1.565 5.505,1.718 0.103,0.154 10 2 5.626,1.65 5.745,1.797 0.119,0.147 10 B 5.626,5.398 5.963,5.553 0.337,0.154 10 GND 5.409,5.308 5.523,5.464 0.114,0.156 10 1 1.638,2.818 2.237,2.968 0.599,0.150 10 8*1, 18*2 1.638,3.431 2.237,3.581 0.599,0.150 10 5*1, 10*2 1.638,4.066 2.163,4.216 0.525,0.150 10 4*1, 1*2 1.638,5.311 2.163,5.461 0.525,0.150 10 1*1, 7*2 1.216,4.797 1.553,4.952 0.337,0.154 10 LED 5.626,4.787 5.963,4.941 0.337,0.154 10 LED 5.409,4.696 5.523,4.852 0.114,0.156 10 5 1.638,4.699 2.163,4.849 0.525,0.150 10 3*1, 6*2

B291664E02
0.701,1.276 1.707,1.423 1.005,0.147 10 Main Body ECU 0.379,6.05 1.963,6.391 1.584,0.341 10 Power Window Regulator Master Switch Assembly 0.916,7.091 2.539,7.240 1.623,0.149 10 : LIN Communication Line 2.84,6.451 4.517,6.600 1.677,0.149 10 *1: w/ Rear Power Window 2.84,6.76 4.642,6.909 1.802,0.149 10 *2: w/o Rear Power Window 5.625,4.166 6.028,4.315 0.404,0.149 10 AUTO 5.625,3.554 6.095,3.696 0.471,0.142 10 DOWN 5.625,2.919 5.836,3.058 0.211,0.140 10 UP 5.33,2.818 5.502,2.965 0.172,0.147 10 10 5.405,3.445 5.503,3.592 0.098,0.147 10 7 5.421,4.082 5.522,4.224 0.100,0.142 10 4 1.082,3.549 1.550,3.700 0.468,0.151 10 DOWN 1.341,2.915 1.552,3.062 0.211,0.147 10 UP 1.132,4.161 1.551,4.319 0.419,0.157 10 AUTO 1.214,5.422 1.551,5.576 0.337,0.154 10 GND 1.643,2.193 2.238,2.343 0.595,0.150 10 6*1, 15*2 1.434,2.279 1.553,2.435 0.119,0.156 10 B 3.674,2.279 4.667,2.435 0.994,0.156 10 from P/W Relay 3.055,1.658 3.831,1.814 0.776,0.156 10 from Battery 4.351,1.806 4.798,1.944 0.448,0.137 10 DOOR 2.777,2.418 3.062,2.563 0.286,0.145 10 P/W 0.379,5.868 0.596,6.021 0.217,0.153 10 G1 5.4,1.577 5.503,1.731 0.103,0.154 10 2 5.625,1.663 5.743,1.809 0.119,0.147 10 B 5.625,5.411 5.961,5.565 0.337,0.154 10 GND 5.407,5.32 5.522,5.476 0.114,0.156 10 1 0.091,0.064 0.760,0.241 0.669,0.177 12 for RHD: 5.182,5.881 5.388,6.025 0.206,0.144 10 G3 5.182,6.043 6.776,6.551 1.593,0.508 10 Power Window Regulator Motor Assembly RH (Driver Side) 1.643,2.816 2.169,2.966 0.525,0.150 10 1*1, 9*2 1.643,3.443 2.169,3.593 0.525,0.150 10 5*1, 6*2 1.643,5.323 2.169,5.473 0.525,0.150 10 9*1, 7*2 1.643,4.078 2.238,4.228 0.595,0.150 10 4*1, 18*2 1.214,4.796 1.551,4.950 0.337,0.154 10 LED 5.625,4.785 5.961,4.939 0.337,0.154 10 LED 5.407,4.695 5.522,4.850 0.114,0.156 10 5 1.643,4.698 2.346,4.847 0.702,0.150 10 3*1, 16*2

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

When the power window regulator motor assembly LH or RH (driver side) is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operations at least 5 times:

(a)

Close the power window by fully pulling up the power window regulator master switch assembly and holding it in the auto up position.

(b)

Open the power window by fully pushing down the power window regulator master switch assembly.


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

According to the display on the intelligent tester, perform the Data List.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto switch signal /
OFF or ON
OFF: Driver side door power window auto switch not operated
ON: Driver side door power window auto switch operated
-
D Door P/W Up SW Driver side power window manual up switch signal /
OFF or ON
OFF: Driver side door power window manual up switch not operated
ON: Driver side door power window manual up switch operated
-
D Door P/W Down SW Driver side power window manual down switch signal /
OFF or ON
OFF: Driver side door power window manual down switch not operated
ON: Driver side door power window manual down switch operated
-

OK:

Normal conditions listed above are displayed.




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / DOWN / UP -

OK:

Driver side door power window operates normally.




OK

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (DRIVER SIDE)

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Inspect the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - P/W RELAY AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - P/W RELAY AND BODY GROUND)
U158224E01
0.109,0.047 0.279,0.207 0.170,0.161 10 *a 0.306,0.464 0.476,0.625 0.170,0.161 10 *A 1.361,0.704 1.531,0.847 0.170,0.144 10 *B 0.224,1.649 0.419,1.830 0.195,0.181 10 H1 2.909,0.792 3.092,0.939 0.184,0.146 10 *C 1.86,2.599 2.044,2.740 0.184,0.142 10 *C 1.231,0.703 1.345,0.847 0.114,0.144 10 B 2.512,0.797 2.839,0.936 0.327,0.140 10 GND 1.711,2.597 1.825,2.741 0.114,0.144 10 B 0.254,2.692 0.582,2.831 0.327,0.140 10 GND 0.664,2.69 0.834,2.832 0.170,0.143 10 *B 1.561,0.777 1.945,1.705 false 2.481,0.867 2.165,1.705 false 1.946,2.158 1.86,2.581 false 0.576,2.678 0.936,1.887 false

a.

for LHD

i.

Disconnect the H1 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Rear Power Window
Tester Connection Switch Condition Specified Condition
H1-6 (B) - Body ground Ignition switch ON 11 to 14 V

w/o Rear Power Window
Tester Connection Switch Condition Specified Condition
H1-15 (B) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
H1-1 (GND) - Body ground Always Below 1 Ω

w/o Rear Power Window
Tester Connection Condition Specified Condition
H1-7 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*A for LHD
*B w/ Rear Power Window
*C w/o Rear Power Window
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)



U158225E01
0.117,0.053 0.287,0.214 0.170,0.161 10 *a 0.315,0.471 0.485,0.631 0.170,0.161 10 *A 1.37,0.71 1.540,0.854 0.170,0.144 10 *B 0.233,1.69 0.446,1.871 0.213,0.181 10 G1 2.917,0.799 3.101,0.945 0.184,0.146 10 *C 1.869,2.605 2.052,2.747 0.184,0.142 10 *C 1.239,0.71 1.354,0.854 0.114,0.144 10 B 2.52,0.803 2.847,0.943 0.327,0.140 10 GND 1.72,2.604 1.834,2.748 0.114,0.144 10 B 2.795,2.58 3.122,2.720 0.327,0.140 10 GND 3.205,2.578 3.375,2.721 0.170,0.143 10 *B 1.57,0.783 1.954,1.711 false 2.489,0.873 2.174,1.711 false 1.955,2.164 1.869,2.588 false 3.094,2.567 2.558,1.891 false

b.

for RHD

i.

Disconnect the G1 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Rear Power Window
Tester Connection Switch Condition Specified Condition
G1-6 (B) - Body ground Ignition switch ON 11 to 14 V

w/o Rear Power Window
Tester Connection Switch Condition Specified Condition
G1-15 (B) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
G1-9 (GND) - Body ground Always Below 1 Ω

w/o Rear Power Window
Tester Connection Condition Specified Condition
G1-7 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*A for RHD
*B w/ Rear Power Window
*C w/o Rear Power Window
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH - BATTERY AND BODY GROUND)
U158226E02
1.135,0.823 1.438,0.938 false 2.313,0.823 2.01,0.938 false 0.083,0.042 0.25,0.198 0.167,0.156 10 false *a 0.333,0.323 0.5,0.479 0.167,0.156 10 false *A 0.573,1.25 0.771,1.427 0.198,0.177 10 false H3 0.708,0.75 1.042,0.927 0.333,0.177 10 false GND 2.354,0.74 2.469,0.896 0.115,0.156 10 false B

a.

for LHD

i.

Disconnect the H3 power window regulator motor assembly LH (driver side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H3-2 (B) - Body ground Always 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*A for LHD
*a Front view of wire harness connector
(to Power Window Regulator Motor Assembly LH (Driver Side))



U158227E02
1.135,0.823 1.448,0.927 false 2.323,0.823 2.01,0.927 false 0.083,0.031 0.25,0.188 0.167,0.156 10 false *a 0.333,0.323 0.5,0.479 0.167,0.156 10 false *A 0.573,1.25 0.781,1.427 0.208,0.177 10 false G3 0.708,0.74 1.042,0.927 0.333,0.188 10 false GND 2.354,0.729 2.469,0.885 0.115,0.156 10 false B

b.

for RHD

i.

Disconnect the G3 power window regulator motor assembly RH (driver side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G3-2 (B) - Body ground Always 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*A for RHD
*a Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH (Driver Side))




OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

for LHD

i.

Disconnect the H1 power window regulator master switch assembly connector.


ii.

Disconnect the H3 power window regulator motor assembly LH (driver side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
H1-8 (UP) - H3-10 (UP) Always Below 1 Ω
H1-5 (DOWN) - H3-7 (DOWN) Always Below 1 Ω
H1-4 (AUTO) - H3-4 (AUTO) Always Below 1 Ω
H1-3 (LED) - H3-5 (LED) Always Below 1 Ω
H1-8 (UP) - Body ground Always 10 kΩ or higher
H1-5 (DOWN) - Body ground Always 10 kΩ or higher
H1-4 (AUTO) - Body ground Always 10 kΩ or higher
H1-3 (LED) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
H1-18 (UP) - H3-10 (UP) Always Below 1 Ω
H1-10 (DOWN) - H3-7 (DOWN) Always Below 1 Ω
H1-1 (AUTO) - H3-4 (AUTO) Always Below 1 Ω
H1-6 (LED) - H3-5 (LED) Always Below 1 Ω
H1-18 (UP) - Body ground Always 10 kΩ or higher
H1-10 (DOWN) - Body ground Always 10 kΩ or higher
H1-1 (AUTO) - Body ground Always 10 kΩ or higher
H1-6 (LED) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the G1 power window regulator master switch assembly connector.


ii.

Disconnect the G3 power window regulator motor assembly RH (driver side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
G1-1 (UP) - G3-10 (UP) Always Below 1 Ω
G1-5 (DOWN) - G3-7 (DOWN) Always Below 1 Ω
G1-4 (AUTO) - G3-4 (AUTO) Always Below 1 Ω
G1-3 (LED) - G3-5 (LED) Always Below 1 Ω
G1-1 (UP) - Body ground Always 10 kΩ or higher
G1-5 (DOWN) - Body ground Always 10 kΩ or higher
G1-4 (AUTO) - Body ground Always 10 kΩ or higher
G1-3 (LED) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
G1-9 (UP) - G3-10 (UP) Always Below 1 Ω
G1-6 (DOWN) - G3-7 (DOWN) Always Below 1 Ω
G1-18 (AUTO) - G3-4 (AUTO) Always Below 1 Ω
G1-16 (LED) - G3-5 (LED) Always Below 1 Ω
G1-9 (UP) - Body ground Always 10 kΩ or higher
G1-6 (DOWN) - Body ground Always 10 kΩ or higher
G1-18 (AUTO) - Body ground Always 10 kΩ or higher
G1-16 (LED) - Body ground Always 10 kΩ or higher





OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (DRIVER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR