Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the front passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor assembly RH or LH (front passenger side), power window regulator switch assembly (front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B291667E01
0.105,0.09 0.766,0.260 0.661,0.170 12 for LHD: 0.124,2.019 1.118,2.184 0.994,0.165 10 from P/W Relay 1.604,2.168 2.181,2.310 0.577,0.142 10 DOOR P 2.55,1.937 2.659,2.084 0.109,0.147 10 3 2.753,2.019 2.867,2.170 0.114,0.151 10 B 0.133,3.961 1.807,4.103 1.674,0.142 10 *1: w/ Rear Power Window 0.133,4.274 1.891,4.416 1.758,0.142 10 *2: w/o Rear Power Window 2.314,3.91 2.539,4.080 0.225,0.170 10 G2 2.314,4.083 4.440,4.415 2.126,0.332 10 Power Window Regulator Switch Assembly (Front Passenger Side) 5.452,3.894 5.654,4.038 0.202,0.144 10 H1 5.127,2.734 5.797,2.885 0.669,0.150 10 16*1, 12*2 5.452,4.05 7.062,4.363 1.610,0.313 10 Power Window Regulator Master Switch Assembly 4.811,1.673 5.041,1.829 0.230,0.156 10 G4 4.811,1.841 7.154,2.173 2.342,0.332 10 Power Window Regulator Motor Assembly RH (Front Passenger Side) 5.686,0.512 5.800,0.678 0.114,0.165 10 2 5.676,1.149 5.781,1.300 0.105,0.151 10 1 4.112,0.517 4.231,0.673 0.119,0.156 10 4 4.112,1.146 4.222,1.302 0.110,0.156 10 1 3.911,0.613 4.035,0.764 0.123,0.151 10 U 3.911,1.243 4.035,1.390 0.123,0.147 10 D 4.112,2.733 4.220,2.886 0.108,0.153 10 5 4.112,3.341 4.208,3.502 0.096,0.161 10 2 3.818,2.816 4.034,2.972 0.216,0.156 10 SU 3.818,3.442 4.034,3.589 0.216,0.147 10 SD 5.887,2.819 6.010,2.970 0.123,0.151 10 U 5.887,3.442 6.010,3.589 0.123,0.147 10 D 5.127,3.346 5.797,3.497 0.669,0.150 10 15*1, 16*2 5.887,0.613 6.010,0.764 0.123,0.151 10 U 5.887,1.243 6.010,1.390 0.123,0.147 10 D

B291667E02
0.091,0.097 0.786,0.267 0.695,0.170 12 for RHD: 0.11,2.026 1.104,2.191 0.994,0.165 10 from P/W Relay 1.59,2.175 2.167,2.317 0.577,0.142 10 DOOR P 2.536,1.944 2.645,2.091 0.109,0.147 10 3 2.739,2.026 2.853,2.177 0.114,0.151 10 B 0.119,3.968 1.793,4.110 1.674,0.142 10 *1: w/ Rear Power Window 0.119,4.281 1.877,4.423 1.758,0.142 10 *2: w/o Rear Power Window 2.3,3.917 2.525,4.087 0.225,0.170 10 H2 2.3,4.09 4.412,4.422 2.112,0.332 10 Power Window Regulator Switch Assembly (Front Passenger Side) 5.438,3.901 5.654,4.045 0.215,0.145 10 G1 5.619,2.741 5.797,2.892 0.178,0.150 10 12 5.438,4.062 7.048,4.375 1.610,0.313 10 Power Window Regulator Master Switch Assembly 4.822,1.68 5.052,1.836 0.230,0.156 10 H4 4.822,1.848 7.140,2.180 2.318,0.332 10 Power Window Regulator Motor Assembly LH (Front Passenger Side) 5.672,0.519 5.786,0.685 0.114,0.165 10 2 5.662,1.156 5.767,1.307 0.105,0.151 10 1 4.098,0.524 4.217,0.680 0.119,0.156 10 4 4.098,1.153 4.208,1.309 0.110,0.156 10 1 3.897,0.62 4.021,0.771 0.123,0.151 10 U 3.897,1.25 4.021,1.397 0.123,0.147 10 D 4.098,2.74 4.206,2.893 0.108,0.153 10 5 4.098,3.348 4.194,3.509 0.096,0.161 10 2 3.804,2.823 4.020,2.979 0.216,0.156 10 SU 3.804,3.449 4.020,3.596 0.216,0.147 10 SD 5.873,2.826 5.996,2.977 0.123,0.151 10 U 5.873,3.449 5.996,3.596 0.123,0.147 10 D 5.122,3.353 5.793,3.504 0.671,0.150 10 13*1, 10*2 5.873,0.62 5.996,0.771 0.123,0.151 10 U 5.873,1.25 5.996,1.397 0.123,0.147 10 D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)
a.

Inspect the power window regulator switch assembly (front passenger side) (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION).



OK

2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR LH (FRONT PASSENGER SIDE)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)

2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR LH (FRONT PASSENGER SIDE)
a.

Inspect the power window regulator motor assembly RH or LH (front passenger side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - P/W RELAY)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR LH (FRONT PASSENGER SIDE)

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - P/W RELAY)
U158228E01
0.083,0.063 0.253,0.224 0.170,0.161 10 *a 0.274,0.412 0.444,0.573 0.170,0.161 10 *A 0.606,1.109 0.808,1.290 0.202,0.181 10 G2 1.786,1.607 1.899,1.752 0.113,0.145 10 B 1.749,1.294 1.845,1.584 false

a.

for LHD

i.

Disconnect the G2 power window regulator switch assembly (front passenger side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-3 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for LHD
*a Front view of wire harness connector
(to Power Window Regulator Switch Assembly (Front Passenger Side))



U158229E01
0.096,0.072 0.266,0.232 0.170,0.161 10 *a 0.339,0.417 0.508,0.577 0.170,0.161 10 *A 0.529,1.104 0.723,1.285 0.195,0.181 10 H2 1.797,1.613 1.915,1.762 0.117,0.149 10 B 1.752,1.289 1.855,1.592 false

b.

for RHD

i.

Disconnect the H2 power window regulator switch assembly (front passenger side) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H2-3 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for RHD
*a Front view of wire harness connector
(to Power Window Regulator Switch Assembly (Front Passenger Side))




OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

for LHD

i.

Disconnect the G2 power window regulator switch assembly (front passenger side) connector.


ii.

Disconnect the G4 power window regulator motor assembly RH (front passenger side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-4 (U) - G4-2 (U) Always Below 1 Ω
G2-1 (D) - G4-1 (D) Always Below 1 Ω
G2-4 (U) - Body ground Always 10 kΩ or higher
G2-1 (D) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the H2 power window regulator switch assembly (front passenger side) connector.


ii.

Disconnect the H4 power window regulator motor assembly LH (front passenger side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-4 (U) - H4-2 (U) Always Below 1 Ω
H2-1 (D) - H4-1 (D) Always Below 1 Ω
H2-4 (U) - Body ground Always 10 kΩ or higher
H2-1 (D) - Body ground Always 10 kΩ or higher





OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.

Disconnect the G2 power window regulator switch assembly (front passenger side) connector.


ii.

Disconnect the H1 power window regulator master switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
G2-5 (SU) - H1-16 (U) Always Below 1 Ω
G2-2 (SD) - H1-15 (D) Always Below 1 Ω
G2-5 (SU) - Body ground Always 10 kΩ or higher
G2-2 (SD) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
G2-5 (SU) - H1-12 (U) Always Below 1 Ω
G2-2 (SD) - H1-16 (D) Always Below 1 Ω
G2-5 (SU) - Body ground Always 10 kΩ or higher
G2-2 (SD) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the H2 power window regulator switch assembly (front passenger side) connector.


ii.

Disconnect the G1 power window regulator master switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
H2-5 (SU) - G1-12 (U) Always Below 1 Ω
H2-2 (SD) - G1-13 (D) Always Below 1 Ω
H2-5 (SU) - Body ground Always 10 kΩ or higher
H2-2 (SD) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
H2-5 (SU) - G1-12 (U) Always Below 1 Ω
H2-2 (SD) - G1-10 (D) Always Below 1 Ω
H2-5 (SU) - Body ground Always 10 kΩ or higher
H2-2 (SD) - Body ground Always 10 kΩ or higher





OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR