Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248391 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

a.

Pass the hood lock control cable into the engine compartment.


b.

Connect the clamps as shown in the illustration.

B284572E01
1.944,1.224 2.094,1.368 0.150,0.143 10 *1 0.956,1.396 1.106,1.539 0.150,0.143 10 *2 1.119,1.468 1.503,1.668 false 1.932,1.293 1.717,1.643 false 2.895,1.819 3.046,1.962 0.150,0.143 10 *1 3.897,1.729 4.047,1.872 0.150,0.143 10 *2 5.826,1.462 5.976,1.605 0.150,0.143 10 *1 6.749,0.98 6.899,1.123 0.150,0.143 10 *3 5.293,3.753 5.443,3.897 0.150,0.143 10 *1 5.538,3.154 5.688,3.298 0.150,0.143 10 *2 1.754,3.736 1.904,3.880 0.150,0.143 10 *1 0.884,4.09 1.034,4.233 0.150,0.143 10 *2 3.882,1.796 3.556,1.796 false 3.037,1.877 3.444,1.799 false 6.725,1.058 6.44,1.214 false 5.984,1.525 6.21,1.243 false 5.688,3.222 5.925,3.481 false 5.443,3.826 5.894,3.78 false 1.035,4.156 1.394,4.208 false 1.734,3.805 1.588,4.188 false

Text in Illustration
*1 Hood Lock Control Cable *2 Clamp
*3 Grommet - -


Hide 53630 2.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

a.

Pass the hood lock control cable into the engine compartment.


b.

Connect the clamps as shown in the illustration.

B284573E01
0.836,0.751 0.988,0.906 0.151,0.155 10 *1 1.171,0.103 1.322,0.258 0.151,0.155 10 *2 1.334,0.174 1.483,0.467 false 0.977,0.82 1.455,0.783 false 0.516,2.301 0.667,2.457 0.151,0.155 10 *2 1.275,1.96 1.427,2.116 0.151,0.155 10 *1 1.26,2.029 1.139,2.386 false 0.662,2.367 0.954,2.414 false 0.516,2.301 0.667,2.457 0.151,0.155 10 *2 1.275,1.96 1.427,2.116 0.151,0.155 10 *1 4.184,2.906 4.335,3.062 0.151,0.155 10 *2 4.084,2.117 4.235,2.272 0.151,0.155 10 *1 1.26,2.029 1.139,2.386 false 0.662,2.367 0.954,2.414 false 1.15,3.955 1.301,4.111 0.151,0.155 10 *2 1.861,3.706 2.013,3.861 0.151,0.155 10 *1 1.846,3.774 1.773,4.04 false 1.296,4.021 1.588,4.069 false 4.269,2.897 4.361,2.668 false 4.24,2.188 4.351,2.494 false 5.641,1.304 5.792,1.460 0.151,0.155 10 *3 4.757,1.846 4.908,2.002 0.151,0.155 10 *1 5.633,1.379 5.374,1.582 false 4.9,1.908 5.135,1.611 false

Text in Illustration
*1 Hood Lock Control Cable *2 Clamp
*3 Grommet - -


Hide 53601 3.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Connect the hood lock control cable to the hood lock control lever.


b.

Engage the 3 claws and install the hood lock control lever.


Hide 53510 4.INSTALL HOOD LOCK ASSEMBLY

a.
B284544

Apply MP grease to the sliding areas of the hood lock.


b.

Connect the hood lock control cable.


c.

Install the hood lock with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53301 6.ADJUST HOOD SUB-ASSEMBLY

Hide 53875A 8.INSTALL FRONT FENDER LINER RH (for RHD)

HINT:

Use the same procedure as for the LH side (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION).