Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2014.07–2016.09
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248393 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 75923 1.INSTALL NO. 2 BLACK OUT TAPE

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION).


Hide 67871 2.INSTALL REAR DOOR WEATHERSTRIP

a.
B271699

Engage the 29 clips to install the rear door weatherstrip.


b.

Install the 2 clips.


Hide 68630D 3.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the rear door check assembly.


b.
B271690

Install the rear door check assembly to the door panel with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the rear door check assembly to the body panel with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69203A 4.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding areas of the rear door outside handle frame sub-assembly.


b.
B373450

Engage the 2 claws and grommet to install the front door outside handle frame sub-assembly.


c.
B373452

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 5.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B271695

Engage the 2 claws to install the rear door outside handle rear pad.


Hide 69241G 6.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B271694

Engage the 3 claws to install the rear door outside handle front pad.


Hide 69230 7.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B271693

Install the rear door outside handle assembly as shown in the illustration.


Hide 69227J 8.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B355531

Engage the 2 claws to install the front door outside handle cover.


b.
B271691

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69050A 9.INSTALL REAR DOOR LOCK ASSEMBLY

Hide 68180C 10.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION).


Hide 68142C 11.INSTALL REAR DOOR GLASS RUN

a.
B271681

Engage the 2 guides to install the rear door glass run.


b.

Install the clip.


Hide 69803 12.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.


b.
B312396E01
1.732,0.064 1.908,0.241 0.177,0.177 10 *a 1.238,0.597 1.689,0.223 false

Temporarily install the temporary bolt to the rear door window regulator sub-assembly.

Text in Illustration
*a Temporary Bolt


c.

Insert the rear door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly on the door panel.


d.

Tighten the 3 bolts and temporary bolt in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 13.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B275488E04
2.661,0.201 2.821,0.364 0.160,0.162 10 *a 0.638,0.201 0.797,0.364 0.160,0.162 10 *b 0.348,0.574 0.552,0.736 0.204,0.162 10 *d 2.743,0.574 2.938,0.736 0.195,0.162 10 *c

Install a new rear door glass channel filler as shown in the illustration.

Text in Illustration
*a Front Side
*b Rear Side
*c 37.3 mm (1.47 in.)
*d 5.1 mm (0.201 in.)


Hide 69905B 14.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to a rear door glass channel sub-assembly.


b.
B275489E04
2.641,0.212 2.809,0.365 0.167,0.154 10 *a 0.622,0.212 0.789,0.365 0.167,0.154 10 *b 0.343,0.597 0.520,0.751 0.178,0.154 10 *d 2.741,0.597 2.938,0.751 0.198,0.154 10 *c

Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel.

Text in Illustration
*a Front Side
*b Rear Side
*c 37.3 mm (1.47 in.)
*d 5.1 mm (0.201 in.)

NOTICE:
·

Be careful not to damage the glass or glass channel.

·

Make sure the position of the rear door glass channel filler does not change.




Hide 68103 15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B372736E01
1.083,0.385 1.24,0.583 0.156,0.198 10 false 1 1.677,0.313 1.833,0.51 0.156,0.198 10 false 2

Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



b.
B271684

Slide the lower section of the rear door glass sub-assembly as indicated by the arrow as shown in the illustration.


Hide 67407E 16.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B271682

Connect the rear door window division bar sub-assembly to the rear door glass run.


b.

Install the rear door window division bar with the 3 bolts and nut.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67841E 17.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.
B271707E01
2.644,3.103 2.804,3.257 0.159,0.154 10 *a 2.833,3.208 2.904,3.088 false 0.118,0.267 0.278,0.421 0.159,0.154 10 *a 0.307,0.373 0.413,0.463 false 3.181,0.302 3.340,0.456 0.159,0.154 10 *a 3.04,0.425 3.178,0.396 false

Install a new rear door service hole cover according to the reference points on the rear door panel.

Text in Illustration
*a Reference Point

HINT:

Securely install the rear door service hole cover taking care to prevent wrinkles.



Hide 68173B 19.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B370699

Engage the 7 claws to install the rear door glass inner weatherstrip as shown in the illustration.


Hide 69205A 20.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B373453

Engage the 4 guides to install the rear door inside handle sub-assembly.


Hide 67603 21.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B373454E02
1.302,1.24 1.021,1.479 false 1.281,0.927 1.219,0.688 false 1.021,0.552 1.188,0.74 0.167,0.188 10 true *1 0.802,1.458 0.979,1.667 0.177,0.208 10 true *2

Connect the rear door lock remote control cable assembly and the rear door inside locking cable assembly to the rear door inside handle sub-assembly.

Text in Illustration
*1 Rear Door Lock Remote Control Cable Assembly
*2 Rear Door Inside Locking Cable Assembly


b.
B369641

Engage the 7 clips to install the rear door trim board sub-assembly.


c.
B373455

Install the 3 screws.


d.
B275408

Engage the claw to close the cover.


Hide 74271A 22.INSTALL REAR DOOR ARMREST BASE UPPER PANEL

a.

Connect the connector.


b.
B369640

Engage the 8 claws and 3 guides to install the rear armrest base upper panel.


Hide 67673A 23.INSTALL REAR DOOR FRAME GARNISH

a.
B271672

Engage the guide.


b.

Engage the 2 clips and claw to install the rear door frame garnish.


Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)