Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.07–2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a communication malfunction is detected between the headlight assembly and main body ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2430 LED Headlight LH Circuit Malfunction Any of the following conditions occur after 20 seconds have elapsed since the Ignition switch was turned ON:
·

Light control ECU malfunction

·

Headlight unit malfunction

·

Light control ECU power source and signal malfunction


·

Light control LED ECU LH

·

Headlight unit LH

·

Semiconductor pwr integration ECU

·

Instrument panel junction block assembly

·

Main body ECU

·

Harness or connector


B2431 LED Headlight RH Circuit Malfunction Any of the following conditions occur after 20 seconds have elapsed since the Ignition switch was turned ON:
·

Light control ECU malfunction

·

Headlight unit malfunction

·

Light control ECU power source and signal malfunction


·

Light control LED ECU RH

·

Headlight unit RH

·

Semiconductor pwr integration ECU

·

Instrument panel junction block assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E295436E03
0.177,0.927 1.094,1.125 0.917,0.198 10 false from Battery 1.542,1.073 2.917,1.271 1.375,0.198 10 false H-LP-MAIN 2.802,0.833 2.979,1.052 0.177,0.219 11 false 1 3.552,0.854 3.708,1.052 0.156,0.198 10 false 2 2.781,1.25 2.938,1.448 0.156,0.198 10 false 3 3.552,1.25 3.708,1.448 0.156,0.198 10 false 5 2.823,1.646 3.823,1.844 1,0.198 10 false H-LP/US-DRL 3.896,0.76 4.208,0.958 0.313,0.198 10 false 18 3.896,0.927 4.208,1.125 0.313,0.198 10 false 3C 5.479,0.771 5.792,0.969 0.313,0.198 10 false 15 5.469,0.927 5.781,1.125 0.313,0.198 10 false MB 5.802,0.927 6.417,1.125 0.615,0.198 10 false HRLY 4.135,1.531 5.688,2.042 1.552,0.51 10 false Instrument Panel Junction Block Assembly 1.188,2.156 1.927,2.417 0.74,0.26 10 false Low Beam 0.5,2.948 0.656,3.146 0.156,0.198 10 false 4 0.698,2.948 0.854,3.146 0.156,0.198 10 false E 2.323,2.729 2.479,2.927 0.156,0.198 10 false S 2.5,2.729 2.667,2.906 0.167,0.177 10 false 1 2.26,3.177 2.573,3.375 0.313,0.198 10 false LO 2.51,3.177 2.667,3.375 0.156,0.198 10 false 5 1.156,2.646 2.167,3.448 1.01,0.802 10 false Light Control LED ECU 0.917,3.938 2.906,4.135 1.99,0.198 10 false Headlight Assembly LH 0.917,3.802 1.375,4 0.458,0.198 10 false A80 2.802,3.417 4.333,3.615 1.531,0.198 10 false H-LP LH LO 5.438,2.625 5.75,2.823 0.313,0.198 10 false 24 5.375,2.833 5.99,3.031 0.615,0.198 10 false F136 5.365,5.271 5.979,5.469 0.615,0.198 10 false F136 5.438,5.073 5.75,5.271 0.313,0.198 10 false 21 5.771,2.823 6.385,3.021 0.615,0.198 10 false LLEW 5.771,5.26 6.385,5.458 0.615,0.198 10 false RLEW 5.615,5.885 6.99,6.083 1.375,0.198 10 false Main Body ECU 1.219,4.594 2.594,4.823 1.375,0.229 10 false Low Beam 1.135,5.094 1.969,5.948 0.833,0.854 10 false Light Control LED ECU 0.51,5.396 0.667,5.594 0.156,0.198 10 false 4 0.698,5.406 0.854,5.604 0.156,0.198 10 false E 2.531,5.177 2.698,5.354 0.167,0.177 10 false 1 2.323,5.188 2.479,5.385 0.156,0.198 10 false S 2.26,5.625 2.573,5.823 0.313,0.198 10 false LO 2.521,5.635 2.677,5.833 0.156,0.198 10 false 5 2.792,5.854 4.323,6.052 1.531,0.198 10 false H-LP RH LO 0.865,6.406 2.854,6.604 1.99,0.198 10 false Headlight Assembly RH 0.865,6.26 1.323,6.458 0.458,0.198 10 false A79

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC B2430 and B2431 are not output if 20 seconds have not elapsed since the Ignition switch was turned ON.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC


Result
Result Proceed to
Both DTCs B2430 and B2431 are not output. A
Both DTCs B2430 and B2431 are output. B
Only DTC B2430 or B2431 is output. C


A

USE SIMULATION METHOD TO CHECK (See page)

B

2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)

C

6.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU POWER SOURCE)
2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)
a.

Remove the headlight relay (H-LP/US-DRL relay).


b.

Inspect the headlight relay (H-LP/US-DRL relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP/US-DRL RELAY)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.
E219671E01
0.138,0.105 0.321,0.260 0.184,0.156 10 *1 1.573,3.099 1.756,3.255 0.184,0.156 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H-LP/US-DRL-1 - Body ground Always 11 to 14 V
H-LP/US-DRL-3 - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block
*2 Headlight Rely (H-LP/US-DRL Relay) Holder



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-LP/US-DRL-2 - 3C-18 Always Below 1 Ω
H-LP/US-DRL-2 or 3C-18 - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U158608E01
5.012,0.383 5.238,0.564 0.225,0.181 10 MB 1.698,0.239 1.893,0.421 0.195,0.181 10 3C 0.103,0.069 0.342,0.257 0.239,0.188 10 *a 5.241,1.261 4.96,0.98 false 5.273,1.198 5.695,1.355 0.422,0.157 10 HRLY

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω




OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL LED ECU POWER SOURCE)
a.

Disconnect the headlight assembly connector.


b.
U158728E01
1.579,1.668 1.818,1.817 0.239,0.149 10 LO 1.849,1.753 2.366,1.237 false 0.197,0.143 0.400,0.311 0.202,0.167 10 *a 1.564,0.796 1.766,0.964 0.202,0.167 10 *b 1.093,0.8 1.358,0.981 0.264,0.181 10 A80 1.093,1.201 1.358,1.382 0.264,0.181 10 A79 1.564,1.197 1.766,1.365 0.202,0.167 10 *c

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH
Tester Connection Condition Specified Condition
A80-5 (LO) - Body ground Ignition switch off, light control switch in head position 11 to 14 V

for RH
Tester Connection Condition Specified Condition
A79-5 (LO) - Body ground Ignition switch off, light control switch in head position 11 to 14 V


Text in Illustration
*a Component with harness connected
(Headlight Assembly)
*b for LH
*c for RH



OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)
a.

Disconnect the A80*1 or A79*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A80-4 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A79-4 (E) - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the A80*1 or A79*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F136 main body ECU connector.


c.
U158729E01
0.273,0.994 0.607,1.176 0.334,0.181 10 F136 1.306,1.916 1.823,1.4 false 1.015,1.94 1.456,2.093 0.441,0.152 10 RLEW 1.788,1.957 2.203,2.110 0.415,0.152 10 LLEW 0.117,0.093 0.336,0.286 0.218,0.193 10 *a 2.039,1.948 2.356,1.4 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH
Tester Connection Condition Specified Condition
F136-24 (LLEW) - Body ground Ignition switch on, light control switch in head position 11 to 14 V

for RH
Tester Connection Condition Specified Condition
F136-21 (RLEW) - Body ground Ignition switch on, light control switch in head position 11 to 14 V


Text in Illustration
*a Component without harness connected
(Main Body ECU)



OK

NG

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the A80*1 or A79*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F136 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A80-1 (S) - F136-24 (LLEW) Always Below 1 Ω
A80-1 (S) or F136-24 (LLEW) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A79-1 (S) - F136-24 (RLEW) Always Below 1 Ω
A79-1 (S) or F136-24 (RLEW) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR