Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2016.09–2017.01
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below.


Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal is released
(c) STP signal is off when ST1- signal is off
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A330504E03
1.083,0.854 1.542,1 0.458,0.146 10 false AM2 1.844,0.854 2.302,1 0.458,0.146 10 false IG2 0.927,0.854 1.021,1.01 0.094,0.156 10 false 5 2.156,0.844 2.25,1 0.094,0.156 10 false 6 0.802,1.281 1.26,1.427 0.458,0.146 10 false F13 0.802,1.417 2.417,1.667 1.615,0.25 10 false Ignition Switch Assembly 1.563,4.156 2.833,4.417 1.271,0.26 10 false Stop Control Relay 0.854,2.667 1.052,2.813 0.198,0.146 10 false 1E 0.854,3.146 1.052,3.292 0.198,0.146 10 false 1C 0.854,4.156 1.052,4.302 0.198,0.146 10 false 1E 2.927,2.125 3.125,2.271 0.198,0.146 10 false 1D 3.365,4.156 3.563,4.302 0.198,0.146 10 false 1D 3.365,3.156 3.563,3.302 0.198,0.146 10 false 1D 3.365,2.469 3.563,2.615 0.198,0.146 10 false 1D 0.865,2.479 1.063,2.625 0.198,0.146 10 false 10 0.906,2.969 1.104,3.115 0.198,0.146 10 false 1 0.906,3.979 1.104,4.125 0.198,0.146 10 false 6 2.625,2.125 2.823,2.271 0.198,0.146 10 false 17 3.406,2.281 3.604,2.427 0.198,0.146 10 false 9 3.365,2.948 3.563,3.094 0.198,0.146 10 false 19 3.406,3.969 3.604,4.115 0.198,0.146 10 false 2 0.198,2.094 0.521,2.24 0.323,0.146 10 false AM2 0.375,3.573 0.615,3.719 0.24,0.146 10 false R/I 0.385,5.594 0.76,5.74 0.375,0.146 10 false MAIN 0.583,6.375 1.208,6.594 0.625,0.219 10 false Battery 1.458,6.031 1.833,6.25 0.375,0.219 10 false ALT 2.969,6.031 3.469,6.25 0.5,0.219 10 false STOP 1.448,4.802 3.167,5 1.719,0.198 10 false No. 1 Integration Relay 1.479,3.469 1.802,3.615 0.323,0.146 10 false IG2 2.417,3.271 2.74,3.417 0.323,0.146 10 false IG2 4.49,1.958 4.688,2.104 0.198,0.146 10 false 4 4.49,3.052 4.688,3.198 0.198,0.146 10 false 2 5.344,3.063 5.542,3.208 0.198,0.146 10 false 1 5.344,1.969 5.542,2.115 0.198,0.146 10 false 3 5.698,3.052 5.896,3.198 0.198,0.146 10 false 9 5.625,1.969 5.917,2.156 0.292,0.188 10 false 10 5.625,0.896 5.906,1.125 0.281,0.229 10 false 37 5.875,0.885 6.281,1.031 0.406,0.146 10 false IGSW 5.875,1.958 6.25,2.146 0.375,0.188 10 false ST1- 5.885,3.042 6.25,3.24 0.365,0.198 10 false STP 6.25,4.229 6.677,4.417 0.427,0.188 10 false ECM 6.271,4.063 6.667,4.25 0.396,0.188 10 false A83 4.427,3.469 4.833,3.615 0.406,0.146 10 false A81 4.427,3.615 5.531,3.979 1.104,0.365 10 false Stop Light Switch Assembly 5.083,4.927 6.052,5.281 0.969,0.354 10 false to Other ECUs

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON and turn the GTS on.

(c)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

(d)

Check the STP signal when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U158066C01
0.167,0.063 0.906,0.385 0.74,0.323 10 false *a 0.729,1.292 1.073,1.5 0.344,0.208 10 false A81
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A81-2 - Body ground Always 11 to 14 V




OK

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U158067C01
0.167,0.063 0.906,0.385 0.74,0.323 10 false *a 0.74,1.292 1.083,1.5 0.344,0.208 10 false A81
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A81-4 - Body ground Ignition switch ON 11 to 14 V




OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

4.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
U134152C02
2.24,3.344 1.958,4.281 true 2.313,3.354 2.677,4.302 true 1.833,0.531 2.635,0.844 0.802,0.313 10 false *b 0.281,0.531 1.052,0.854 0.771,0.323 10 false *a 0.417,2.552 0.677,2.76 0.26,0.208 10 false *c 1.823,4.344 2.167,4.542 0.344,0.198 10 false STP 2.594,4.333 2.969,4.542 0.375,0.208 10 false ST1- 0.271,3.458 0.594,3.667 0.323,0.208 10 false A83
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-9 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A81 stop light switch connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A81-4 - 1D-19 Always Below 1 Ω
A81-4 or 1D-19 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR