Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using an electric motor and gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This electronic throttle control system does not use a throttle cable.


DTC No. DTC Detection Condition Trouble Area
P2102 Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio 80% or more
(b) Throttle actuator current less than 0.5 A
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either of the following conditions is met (1 trip detection logic):
·

Hybrid IC diagnosis signal failure

·

Hybrid IC current limiter port failure


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM



MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, if the throttle actuator is stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

Example:

When the electrical current is below 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved to a high engine speed several times after the engine has idled for 5 seconds after engine start.


MONITOR STRATEGY

Required Sensors/Components Throttle actuator (throttle body with motor assembly)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199313E89
3.656,1.458 3.229,0.406 3.229,0.406 3.521,0.406 false 4.823,2 5.25,1.135 5.25,1.135 5.406,1.135 false 2.656,2 2.448,1.208 2.448,1.208 2.615,1.208 false 1.25,1.844 1.625,2.01 0.375,0.167 10 false Idling 0.427,2.115 1.625,2.26 1.198,0.146 10 false Ignition Switch ON 2.125,2.042 2.448,2.292 0.323,0.25 10 false [A] 3.854,1.74 4.188,1.958 0.333,0.219 10 false [B] 5.458,1.042 6.094,1.188 0.635,0.146 10 false Released 3.594,0.313 4.323,0.458 0.729,0.146 10 false Depressed 3.49,2.719 4.688,2.906 1.198,0.188 10 false 2 seconds or more 5.26,3.323 5.5,3.531 0.24,0.208 10 false [C] 3.625,3.042 5.24,3.229 1.615,0.188 10 false 16 seconds or more 2.667,1.115 3.302,1.26 0.635,0.146 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].

8.

Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2102 or P2103.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and, if necessary, drive the vehicle for a period of time.




FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A254091E06
1.104,1.125 1.396,1.292 0.292,0.167 10 false M+ 1.135,1.885 1.396,2.042 0.26,0.156 10 false M- 2.646,2.573 3.365,2.781 0.719,0.208 10 false (Shielded) 1.448,1.135 1.625,1.313 0.177,0.177 10 false 2 1.448,1.885 1.635,2.073 0.188,0.188 10 false 1 4.583,1.063 4.813,1.229 0.229,0.167 10 false 60 4.594,1.813 4.813,2.01 0.219,0.198 10 false 30 4.573,2.563 4.781,2.781 0.208,0.219 10 false 58 4.542,2.74 4.854,2.927 0.313,0.188 10 false B89 4.542,1.25 4.854,1.417 0.313,0.167 10 false B89 4.552,1.99 4.875,2.188 0.323,0.198 10 false B89 0.177,2.5 0.49,2.667 0.313,0.167 10 false B29 0.177,2.656 2.49,2.844 2.313,0.188 10 false Throttle Body with Motor Assembly 4.885,1.146 5.167,1.344 0.281,0.198 10 false M+ 4.885,1.875 5.125,2.083 0.24,0.208 10 false M- 4.885,2.729 5.333,2.938 0.448,0.208 10 false GE01 5.26,1.208 6.406,1.406 1.146,0.198 10 false Throttle Actuator 5.26,1.552 6.229,1.74 0.969,0.188 10 false Control Circuit 5.729,3.313 6.75,3.615 1.021,0.302 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the B29 throttle body with motor assembly connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-2 (M+) - B89-60 (M+) Always Below 1 Ω
B29-1 (M-) - B89-30 (M-) Always Below 1 Ω
B29-2 (M+) or B89-60 (M+) - Body ground Always 10 kΩ or higher
B29-1 (M-) or B89-30 (M-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between throttle valve and housing.


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY