Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM J

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).


WIRING DIAGRAM

A254125E16
0.677,4.542 1.177,4.677 0.5,0.135 10 false Battery 0.563,3.083 0.927,3.24 0.365,0.156 10 false MAIN 1.74,1.031 2.063,1.177 0.323,0.146 10 false AM2 2.792,1.406 4.313,1.802 1.521,0.396 10 false Ignition or Starter Switch Assembly 2.563,1.896 3.99,2.219 1.427,0.323 10 false Park/Neutral Position Switch*1 2.604,3.25 4.583,3.427 1.979,0.177 10 false Clutch Start Switch Assembly*2 2.396,4.448 2.625,4.594 0.229,0.146 10 false ST 3.458,4.646 3.688,4.802 0.229,0.156 10 false ST 4.146,4.688 5.396,4.844 1.25,0.156 10 false to Starter Assembly 6.146,5.031 6.49,5.188 0.344,0.156 10 false ECM 3.094,4.219 3.198,4.385 0.104,0.167 10 false 5 3.094,3.906 3.198,4.073 0.104,0.167 10 false 2 3.885,4.219 3.99,4.385 0.104,0.167 10 false 3 3.885,3.906 3.99,4.073 0.104,0.167 10 false 1 2.563,1.75 2.833,1.896 0.271,0.146 10 false B88 2.615,3.104 3.031,3.26 0.417,0.156 10 false A39 3.073,0.802 3.385,0.948 0.313,0.146 10 false AM2 3.781,0.802 4.063,0.948 0.281,0.146 10 false ST2 2.865,0.813 2.979,0.958 0.115,0.146 10 false 5 4.177,0.813 4.292,0.958 0.115,0.146 10 false 7 4.479,2.354 4.583,2.51 0.104,0.156 10 false 5 3.063,2.708 3.219,2.865 0.156,0.156 10 false 1 4.458,1.521 4.563,1.677 0.104,0.156 10 false 4 3.969,2.708 4.115,2.865 0.146,0.156 10 false 2 5.427,3.365 5.656,3.573 0.229,0.208 10 false 22 5.427,2.656 5.708,2.885 0.281,0.229 10 false 63 5.406,3.521 5.792,3.729 0.385,0.208 10 false A83 5.406,2.813 5.76,2.958 0.354,0.146 10 false B89 5.76,3.521 6.052,3.677 0.292,0.156 10 false STA 5.771,2.823 6.125,2.979 0.354,0.156 10 false NSW 2.646,1.24 2.927,1.396 0.281,0.156 10 false F13 4.354,1.74 4.521,1.958 0.167,0.219 10 false L 4.594,1.74 4.76,1.958 0.167,0.219 10 false B 4.094,1.948 4.26,2.104 0.167,0.156 10 false P 4.094,2.125 4.26,2.281 0.167,0.156 10 false N 3.927,5.135 5.656,5.323 1.729,0.188 10 false *1: for Automatic Transaxle 3.927,5.406 5.76,5.563 1.833,0.156 10 false *2: for Manual Transaxle 4.771,1.552 4.969,1.74 0.198,0.188 10 false *1 4.448,2.896 4.698,3.094 0.25,0.198 10 false *2 2.427,2.896 2.677,3.094 0.25,0.198 10 false *2 2.625,2.521 2.823,2.708 0.198,0.188 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if engine can be cranked.

Result
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

13.READ VALUE USING GTS
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the result when the ignition switch is turned to ON and the engine starts.


OK:
Ignition Switch Position Starter Signal
ON OFF
START ON


Result
Result Proceed to
NG (for Manual Transaxle) A
NG (for Automatic Transaxle) B
OK (for Manual Transaxle) C
OK (for Automatic Transaxle) D


A

3.INSPECT CLUTCH START SWITCH ASSEMBLY

B

7.INSPECT PARK/NEUTRAL POSITION SWITCH

C

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM - ST RELAY)

D

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - ST RELAY)
3.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

4.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

4.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the F13 ignition switch assembly connector.


b.

Disconnect the A39 clutch start switch assembly connector.


c.

Disconnect the B89 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (ST2) - A39-2 Always Below 1 Ω
F13-7 (ST2) - B89-63 (NSW) Always Below 1 Ω
F13-7 (ST2) or A39-2 - Body ground Always 10 kΩ or higher
F13-7 (ST2) or B89-63 (NSW) - Body ground Always 10 kΩ or higher



OK

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the A83 ECM connector.


c.

Disconnect the A39 clutch start switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - A83-22 (STA) Always Below 1 Ω
2 (ST relay) - A39-1 Always Below 1 Ω
A83-22 (STA), A39-1 or 2 (ST relay) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

11.INSPECT BATTERY
7.INSPECT PARK/NEUTRAL POSITION SWITCH

OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE PARK/NEUTRAL POSITION SWITCH

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH
a.

Disconnect the F13 ignition switch assembly connector.


b.

Disconnect the B88 park/neutral position switch connector.


c.

Disconnect the B89 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (ST2) - B88-4 (B) Always Below 1 Ω
F13-7 (ST2) - B89-63 (NSW) Always Below 1 Ω
F13-7 (ST2) or B88-4 (B) - Body ground Always 10 kΩ or higher
F13-7 (ST2) or B89-63 (NSW) - Body ground Always 10 kΩ or higher



OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the A83 ECM connector.


c.

Disconnect the B88 park/neutral position switch connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - A83-22 (STA) Always Below 1 Ω
2 (ST relay) - B88-5 (L) Always Below 1 Ω
A83-22 (STA) or B88-5 (L) - Body ground Always 10 kΩ or higher



OK

11.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BATTERY
a.

Check that the battery is not depleted.


OK:

Battery is not depleted.



OK

12.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

12.CHECK BATTERY TERMINAL
a.

check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE BATTERY TERMINAL

13.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

14.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
14.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the A83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-22 (STA) - 2 (ST relay) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR