Use the same procedure for both the RH and LH sides.
The procedure described below is for the RH side.
75923
1.INSTALL NO. 2 BLACK OUT TAPE
Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION).
67871
2.INSTALL REAR DOOR WEATHERSTRIP
Engage the 29 clips to install the rear door weatherstrip.
Install the 2 clips.
68630D
3.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding areas of the rear door check assembly.
Install the rear door check assembly to the door panel with the 2 bolts.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly to the body panel with the bolt.
69203A
4.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding areas of the rear door outside handle frame sub-assembly.
Engage the 2 claws and grommet to install the front door outside handle frame sub-assembly.
Using a T30 "TORX" socket wrench, tighten the screw.
69242G
5.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
Engage the 2 claws to install the rear door outside handle rear pad.
69241G
6.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
Engage the 3 claws to install the rear door outside handle front pad.
69230
7.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Install the rear door outside handle assembly as shown in the illustration.
69227J
8.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the 2 claws to install the front door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
69330
9.INSTALL REAR DOOR LOCK ASSEMBLY
68180C
10.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION).
68142C
11.INSTALL REAR DOOR GLASS RUN
Engage the 2 guides to install the rear door glass run.
Install the clip.
69803
12.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.
Temporarily install the temporary bolt to the rear door window regulator sub-assembly.
| *a | Temporary Bolt |
Insert the rear door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly on the door panel.
Tighten the 3 bolts and temporary bolt in the order shown in the illustration.
Connect the connector.
69975A
13.INSTALL REAR DOOR GLASS CHANNEL FILLER
Apply soapy water to a new rear door glass channel filler.
Install a new rear door glass channel filler as shown in the illustration.
| *a | Front Side |
| *b | Rear Side |
| *c | 37.3 mm (1.47 in.) |
| *d | 5.1 mm (0.201 in.) |
69905B
14.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
Apply soapy water to a rear door glass channel sub-assembly.
Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel.
| *a | Front Side |
| *b | Rear Side |
| *c | 37.3 mm (1.47 in.) |
| *d | 5.1 mm (0.201 in.) |
Be careful not to damage the glass or glass channel.
Make sure the position of the rear door glass channel filler does not change.
68103
15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.
Do not damage the rear door glass sub-assembly.
Slide the lower section of the rear door glass sub-assembly as indicated by the arrow as shown in the illustration.
67407E
16.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Connect the rear door window division bar sub-assembly to the rear door glass run.
Install the rear door window division bar with the 3 bolts and nut.
67841E
17.INSTALL REAR DOOR SERVICE HOLE COVER
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
Install a new rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
Securely install the rear door service hole cover taking care to prevent wrinkles.
86160B
18.INSTALL REAR SPEAKER ASSEMBLY
68173B
19.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
Engage the 7 claws to install the rear door glass inner weatherstrip as shown in the illustration.
69205A
20.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 4 guides to install the rear door inside handle sub-assembly.
67603
21.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Connect the rear door lock remote control cable assembly and the rear door inside locking cable assembly to the rear door inside handle sub-assembly.
| *1 | Rear Door Lock Remote Control Cable Assembly |
| *2 | Rear Door Inside Locking Cable Assembly |
Engage the 7 clips to install the rear door trim board sub-assembly.
Install the 3 screws.
Engage the claw to close the cover.
74271A
22.INSTALL REAR DOOR ARMREST BASE UPPER PANEL
Connect the connector.
Engage the 8 claws and 3 guides to install the rear armrest base upper panel.
67673A
23.INSTALL REAR DOOR FRAME GARNISH
Engage the guide.
Engage the 2 clips and claw to install the rear door frame garnish.
24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
25.INSPECT POWER WINDOW OPERATION