Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the EFI MAIN relay coil, closing the EFI MAIN relay contacts and supplying power to terminal +B and +B2 of the ECM.

WIRING DIAGRAM

A254094E10
6.083,5.302 6.271,5.458 0.188,0.156 10 false E1 6.083,4.729 6.5,4.875 0.417,0.146 10 false MREL 6.083,4.302 6.375,4.448 0.292,0.146 10 false +B2 6.083,3.854 6.281,4 0.198,0.146 10 false +B 6.083,2.958 6.479,3.104 0.396,0.146 10 false IGSW 5.719,5.271 6.083,5.5 0.365,0.229 10 false B89 5.708,4.698 5.979,4.844 0.271,0.146 10 false A83 5.729,4.271 6,4.417 0.271,0.146 10 false A83 5.729,3.833 6,3.979 0.271,0.146 10 false A83 4.49,2.969 4.698,3.115 0.208,0.146 10 false 1D 4.49,4.292 4.698,4.438 0.208,0.146 10 false 1E 4.49,4.719 4.698,4.865 0.208,0.146 10 false 1D 1.688,2.958 1.896,3.104 0.208,0.146 10 false 1C 1.688,4.719 1.885,4.865 0.198,0.146 10 false 1E 3.969,2.667 4.188,2.813 0.219,0.146 10 false 1D 5.708,2.938 6.063,3.083 0.354,0.146 10 false A83 0.594,5 1.063,5.146 0.469,0.146 10 false Battery 0.448,4.094 0.823,4.24 0.375,0.146 10 false MAIN 0.813,3.115 1.021,3.26 0.208,0.146 10 false R/I 1.708,4.51 1.896,4.656 0.188,0.146 10 false 10 1.75,2.771 1.844,2.917 0.094,0.146 10 false 1 2.865,3.542 3.115,3.688 0.25,0.146 10 false IG2 3.594,3.083 3.844,3.24 0.25,0.156 10 false IG2 2.51,4.406 3.135,4.552 0.625,0.146 10 false EFI MAIN 3.188,4.958 3.823,5.115 0.635,0.156 10 false EFI MAIN 4.542,4.51 4.646,4.656 0.104,0.146 10 false 7 4.542,4.073 4.646,4.219 0.104,0.146 10 false 4 4.542,2.771 4.646,2.917 0.104,0.146 10 false 9 3.677,2.667 3.854,2.813 0.177,0.146 10 false 17 1.406,1.448 1.719,1.594 0.313,0.146 10 false AM2 2.302,1.823 3.448,2.146 1.146,0.323 10 false Ignition Switch Assembly 3.073,1.229 3.323,1.375 0.25,0.146 10 false IG2 2.344,1.229 2.646,1.375 0.302,0.146 10 false AM2 2.5,5.427 4.021,5.604 1.521,0.177 10 false No. 1 Integration Relay 5.76,5.094 6.01,5.24 0.25,0.146 10 false 16 5.76,4.521 5.99,4.74 0.229,0.219 10 false 46 5.802,4.094 6,4.25 0.198,0.156 10 false 3 5.802,3.646 5.896,3.792 0.094,0.146 10 false 2 5.75,2.76 6,2.979 0.25,0.219 10 false 37 6.323,6.01 6.667,6.167 0.344,0.156 10 false ECM 2.198,1.219 2.313,1.375 0.115,0.156 10 false 5 3.375,1.208 3.49,1.365 0.115,0.156 10 false 6 2.302,1.646 2.594,1.833 0.292,0.188 10 false F13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.INSPECT NO. 1 INTEGRATION RELAY (POWER SOURCE)
U126247C01
0.26,0.135 0.479,0.323 0.219,0.188 10 false *a 0.656,1.115 0.938,1.302 0.281,0.188 10 false 1C
*a Front view of wire harness connector
(to No. 1 Integration Relay)


a.

Remove the No. 1 integration relay connector from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V




OK

2.INSPECT NO.1 INTEGRATION RELAY (EFI MAIN RELAY AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)

2.INSPECT NO.1 INTEGRATION RELAY (EFI MAIN RELAY AND IG2 RELAY)
a.

Inspect the No. 1 integration relay (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the A83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-46 (MREL) - 1D-7 Always Below 1 Ω
A83-2 (+B) - 1E-4 Always Below 1 Ω
A83-3 (+B2) - 1E-4 Always Below 1 Ω
A83-46 (MREL) or 1D-7 - Body ground Always 10 kΩ or higher
A83-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher
A83-3 (+B2) or 1E-4 - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the B89 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-16 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW TERMINAL VOLTAGE)
a.
U134131C02
1.531,1.24 2.073,1.979 true 1.75,3.615 2.188,4.323 true 1.583,2.542 1.99,2.76 0.406,0.219 10 false A83 1.583,0.5 1.927,0.719 0.344,0.219 10 false B89 2.115,1.917 2.396,2.115 0.281,0.198 10 false E1 2.26,4.25 2.677,4.469 0.417,0.219 10 false IGSW 0.115,0.063 0.344,0.25 0.229,0.188 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Turn the ignition switch assembly to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A83-37 (IGSW) - B89-16 (E1) Ignition switch ON 11 to 14 V



Result
Result Proceed to
NG A
OK B


A

6.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room main relay block.


b.

Disconnect the A83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-37 (IGSW) - 1D-9 Always Below 1 Ω
A83-37 (IGSW) or 1D-9 - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the F13 ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-17 - F13-6 (IG2) Always Below 1 Ω
1E-10 - Body ground Always Below 1 Ω
F13-6 (IG2) or 1D-17 - Body ground Always 10 kΩ or higher




OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY