Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A254573E03
4.88,3.228 5.251,3.394 0.371,0.166 10 ECM 5.434,1.876 6.416,2.032 0.982,0.156 10 Microprocessor 4.481,0.979 6.283,1.149 1.802,0.170 10 5 V Constant Voltage Circuit 0.329,2.759 2.666,3.102 2.336,0.343 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 0.329,1.848 2.659,2.344 2.330,0.496 10 Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 1.277,0.869 2.641,1.039 1.364,0.170 10 from EFI MAIN Fuse 1.277,1.217 2.607,1.380 1.330,0.163 10 from EFI MAIN Relay 2.863,1.331 3.394,1.480 0.531,0.149 10 +B, +B2 2.937,0.979 3.350,1.144 0.413,0.165 10 BATT 3.227,2.261 3.437,2.412 0.210,0.150 10 VC 4.127,2.874 4.248,3.016 0.121,0.142 10 R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A254095E31
4.583,1.073 4.917,1.25 0.333,0.177 10 false B89 0.396,2.385 2.719,2.615 2.323,0.229 10 false Throttle Body with Motor Assembly 0.396,5.292 2.76,5.469 2.365,0.177 10 false Accelerator Pedal Sensor Assembly 1.979,0.698 2.229,0.875 0.25,0.177 10 false VC 1.792,2.927 2.219,3.104 0.427,0.177 10 false VCPA 1.792,3.292 2.208,3.469 0.417,0.177 10 false VCP2 1.885,3.677 2.229,3.854 0.344,0.177 10 false VPA 1.813,4.031 2.219,4.208 0.406,0.177 10 false VPA2 1.885,4.417 2.198,4.594 0.313,0.177 10 false EPA 1.813,4.771 2.198,4.948 0.385,0.177 10 false EPA2 4.917,2.854 5.531,3.031 0.615,0.177 10 false VCPA 4.917,3.24 5.531,3.417 0.615,0.177 10 false VCP2 4.917,3.667 5.531,3.844 0.615,0.177 10 false VPA 4.917,4.052 5.531,4.229 0.615,0.177 10 false VPA2 4.917,4.333 5.531,4.51 0.615,0.177 10 false EPA 4.917,4.698 5.531,4.875 0.615,0.177 10 false EPA2 1.896,1.063 2.208,1.24 0.313,0.177 10 false VTA 1.813,1.427 2.208,1.604 0.396,0.177 10 false VTA2 1.99,1.813 2.208,1.99 0.219,0.177 10 false E2 4.917,0.625 5.531,0.802 0.615,0.177 10 false VCTA 5.521,5.479 5.865,5.656 0.344,0.177 10 false ECM 4.917,1.063 5.531,1.24 0.615,0.177 10 false VTA1 4.917,1.438 5.531,1.615 0.615,0.177 10 false VTA2 4.917,1.75 5.531,1.927 0.615,0.177 10 false ETA 0.396,5.167 0.667,5.344 0.271,0.177 10 false A36 0.396,2.26 0.677,2.417 0.281,0.156 10 false B29 4.573,1.833 4.917,2 0.344,0.167 10 false B89 4.552,3.677 4.917,3.917 0.365,0.24 10 false A83 4.573,4.042 4.844,4.188 0.271,0.146 10 false A83 4.563,4.427 4.979,4.677 0.417,0.25 10 false A83 4.563,4.802 4.896,5.031 0.333,0.229 10 false A83 4.563,2.938 4.917,3.083 0.354,0.146 10 false A83 4.563,3.313 4.938,3.5 0.375,0.188 10 false A83 4.563,1.448 4.979,1.677 0.417,0.229 10 false B89 4.563,0.698 4.833,0.844 0.271,0.146 10 false B89 4.573,1.677 4.958,1.854 0.385,0.177 10 false 116 4.604,3.135 4.833,3.333 0.229,0.198 10 false 56 4.594,3.521 4.896,3.771 0.302,0.25 10 false 51 4.604,4.625 4.833,4.854 0.229,0.229 10 false 55 4.604,4.25 4.833,4.5 0.229,0.25 10 false 52 4.594,3.875 4.813,4.083 0.219,0.208 10 false 54 4.604,2.76 4.917,2.917 0.313,0.156 10 false 53 4.625,1.271 4.885,1.427 0.26,0.156 10 false 83 4.615,0.896 4.875,1.052 0.26,0.156 10 false 84 4.583,0.542 4.969,0.698 0.385,0.156 10 false 115 2.292,1.365 2.385,1.521 0.094,0.156 10 false 4 2.292,1.719 2.385,1.875 0.094,0.156 10 false 3 2.292,2.823 2.385,2.979 0.094,0.156 10 false 4 2.292,3.198 2.385,3.354 0.094,0.156 10 false 1 2.292,4.688 2.385,4.844 0.094,0.156 10 false 2 2.292,4.323 2.385,4.479 0.094,0.156 10 false 5 2.292,3.948 2.385,4.104 0.094,0.156 10 false 3 2.292,3.573 2.385,3.729 0.094,0.156 10 false 6 2.292,0.979 2.385,1.135 0.094,0.156 10 false 6 2.292,0.594 2.385,0.75 0.094,0.156 10 false 5 5.833,0.458 6.094,0.625 0.26,0.167 10 false 5 V

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for communication between the GTS and ECM.

Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the B29 throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



A

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the A36 accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the B29 throttle body with motor assembly connector.


b.

Disconnect the A36 accelerator pedal sensor assembly connector.


c.

Disconnect the A83 and B89 ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-115 (VCTA) or B29-5 (VC) - Body ground Always 10 kΩ or higher
A83-53 (VCPA) or A36-4 (VCPA) - Body ground Always 10 kΩ or higher
A83-56 (VCP2) or A36-1 (VCP2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR