Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM.

When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground, which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A254126E08
0.49,1.708 0.865,1.875 0.375,0.167 10 false AM2 1.063,0.49 1.427,0.667 0.365,0.177 10 false AM2 1.667,0.479 1.948,0.667 0.281,0.188 10 false IG2 0.75,0.76 1.094,0.927 0.344,0.167 10 false F13 0.75,0.917 2.281,1.323 1.531,0.406 10 false Ignition or Starter Switch Assembly 0.781,4 1.031,4.167 0.25,0.167 10 false R/I 0.49,4.229 0.948,4.458 0.458,0.229 10 false MAIN 0.656,4.927 1.125,5.125 0.469,0.198 10 false Battery 1.979,2.479 2.313,2.635 0.333,0.156 10 false MET 2.656,3.167 2.938,3.344 0.281,0.177 10 false IG2 2.5,4.198 4.229,4.396 1.729,0.198 10 false No. 1 Integration Relay 2.302,3.969 2.563,4.125 0.26,0.156 10 false 1E 2.729,2.188 2.99,2.344 0.26,0.156 10 false 1D 5.74,2.177 6.073,2.344 0.333,0.167 10 false A83 2.302,1.781 2.563,1.938 0.26,0.156 10 false 1D 1.521,3.844 1.781,4 0.26,0.156 10 false 1C 1.99,3.958 2.198,4.125 0.208,0.167 10 false 10 1.573,3.635 1.76,3.802 0.188,0.167 10 false 1 2,1.781 2.219,1.948 0.219,0.167 10 false 17 2.781,1.979 2.906,2.146 0.125,0.167 10 false 6 0.906,0.292 1.021,0.438 0.115,0.146 10 false 5 1.99,0.271 2.104,0.438 0.115,0.167 10 false 6 5.781,1.969 5.99,2.156 0.208,0.188 10 false 27 6.094,2.042 6.344,2.24 0.25,0.198 10 false W 4.781,2.354 5.104,2.521 0.323,0.167 10 false CHK 4.01,2.333 4.302,2.531 0.292,0.198 10 false IG+ 5.24,1.969 5.438,2.146 0.198,0.177 10 false 11 3.708,1.958 3.917,2.146 0.208,0.188 10 false 39 6.396,3.271 6.76,3.469 0.365,0.198 10 false ECM 3.677,2.698 5.635,2.875 1.958,0.177 10 false Combination Meter Assembly 3.708,2.167 3.979,2.354 0.271,0.188 10 false F1 5.24,2.188 5.49,2.354 0.25,0.167 10 false F1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if DTCs have been stored. If DTCs are present, write them down.



e.

Check that the MIL turns off.

OK:

MIL turns off.




OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
U134135C02
0.115,0.094 0.375,0.323 0.26,0.229 10 false *a 1.635,0.313 1.99,0.552 0.354,0.24 10 false A83
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the A83 ECM connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-11 (CHK) or A83-27 (W) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminates when the ignition switch is turned to ON.

OK:

MIL is illuminated.




OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start * B

HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the A83 ECM connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-11 (CHK) - A83-27 (W) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR