Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 2 main lines and/or a central gateway ECU (network gateway ECU) branch line when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

Central gateway ECU (network gateway ECU) branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

No. 1 junction connector

·

No. 2 junction connector



This malfunction is not related to the lines of a bus 2 main bus branch or to ECUs or sensors connected a bus 2 main bus branch.

WIRING DIAGRAM

E352799E02
5.292,0.458 5.906,0.656 0.615,0.198 10 false CANH 5.292,3.958 5.906,4.156 0.615,0.198 10 false CANH 1.406,0.542 2.021,0.74 0.615,0.198 10 false CA4H 5.292,0.875 5.906,1.073 0.615,0.198 10 false CANL 5.292,4.385 5.906,4.583 0.615,0.198 10 false CANL 1.406,0.969 2.021,1.167 0.615,0.198 10 false CA4L 4.208,1.979 4.823,2.177 0.615,0.198 10 false F83 4.208,2.146 6.094,2.406 1.885,0.26 10 false No. 2 Junction Connector 5.594,4.896 6.052,5.094 0.458,0.198 10 false A83 5.594,5.042 6.052,5.24 0.458,0.198 10 false ECM 5.042,3.948 5.354,4.146 0.313,0.198 10 false 13 5.052,4.385 5.365,4.583 0.313,0.198 10 false 26 4.156,4.042 4.615,4.24 0.458,0.198 10 false A61 4.167,4.469 4.625,4.667 0.458,0.198 10 false A61 4.24,3.875 4.552,4.073 0.313,0.198 10 false 9 4.208,4.302 4.521,4.5 0.313,0.198 10 false 20 2.75,4.938 4.542,5.219 1.792,0.281 10 false No. 1 Junction Connector 3.146,3.646 3.76,3.844 0.615,0.198 10 false F82 3.698,3.646 4.313,3.844 0.615,0.198 10 false F82 4.052,3.646 4.208,3.844 0.156,0.198 10 false 4 2.875,3.656 3.188,3.854 0.313,0.198 10 false 15 3.063,2.646 3.375,2.844 0.313,0.198 10 false 21 3.844,2.646 4.156,2.844 0.313,0.198 10 false 10 4.854,1.375 5.469,1.573 0.615,0.198 10 false F1 4.854,1.531 6.854,1.74 2,0.208 10 false Combination Meter Assembly 5.042,0.458 5.354,0.656 0.313,0.198 10 false 32 5.042,0.875 5.354,1.073 0.313,0.198 10 false 31 4.177,0.438 4.49,0.635 0.313,0.198 10 false 7 4.167,0.896 4.479,1.094 0.313,0.198 10 false 18 2.781,0.438 3.094,0.635 0.313,0.198 10 false 9 2.74,0.885 3.052,1.083 0.313,0.198 10 false 22 1.865,0.458 2.177,0.656 0.313,0.198 10 false 18 1.875,0.885 2.188,1.083 0.313,0.198 10 false 17 0.469,1.385 1.083,1.583 0.615,0.198 10 false F139 0.469,1.542 2.438,2.01 1.969,0.469 10 false Central Gateway ECU (Network Gateway ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U161120C03
1.677,1.115 1.229,1.781 true 1.76,1.115 2.167,1.76 true 1.5,0.313 1.844,0.49 0.344,0.177 10 false F139 0.115,0.063 0.448,0.271 0.333,0.208 10 false *a 0.927,1.76 1.594,1.979 0.667,0.219 10 false CA4H 2.042,1.771 2.708,1.99 0.667,0.219 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-18 (CA4H) - F139-17 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the central gateway ECU (network gateway ECU) branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>HOW TO PROCEED WITH TROUBLESHOOTING).




OK

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
a.
U161354C03
1.75,1.271 1.24,1.792 true 1.927,1.271 2.448,1.792 true 1.635,0.302 1.875,0.521 0.24,0.219 10 false F1 0.094,0.031 0.385,0.188 0.292,0.156 10 false *a 2.5,1.708 2.917,1.865 0.417,0.156 10 false CANH 0.74,1.708 1.156,1.865 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-32 (CANH) - F1-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the F1 combination meter assembly connector.


b.
E351558C01
1.75,0.333 2.25,0.583 0.5,0.25 1.781,2.74 2.865,1.656 true 2.198,0.833 2.865,1.5 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.75,0.729 2.365,0.927 0.615,0.198 10 false CANH 1.344,2.635 1.958,2.833 0.615,0.198 10 false CANL 1.885,0.365 2.5,0.563 0.615,0.198 10 false A83
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-13 (CANH) - A83-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


A

4.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 JUNCTION CONNECTOR)

B

C

4.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the A83 ECM connector.


b.
U160864C02
2.198,1.365 2.417,0.521 true 2.208,1.563 2.427,1.938 true 1.854,1.365 1.125,0.521 true 1.833,1.563 1.104,1.938 true 0.104,0.073 0.385,0.313 0.281,0.24 10 false *a 0.563,1.229 0.875,1.417 0.313,0.188 10 false F83 0.594,0.396 1.177,0.625 0.583,0.229 10 false CANH*b 0.583,1.854 1.156,2.073 0.573,0.219 10 false CANL*b 2.458,0.406 3.042,0.635 0.583,0.229 10 false CANH*c 2.458,1.865 3.031,2.083 0.573,0.219 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Combination Meter Assembly
*c to No. 1 Junction Connector


Disconnect the No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F83-7 (CANH) - F83-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F83-10 (CANH) - F83-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 junction connector


Result
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (No. 1 junction connector main line) C



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the F83 No. 2 junction connector.


b.
U160865C03
1.479,1.365 1.094,0.521 true 1.5,1.563 1.115,1.938 true 0.104,0.104 0.333,0.354 0.229,0.25 10 false *a 0.573,1.229 0.969,1.396 0.396,0.167 10 false F82 0.552,0.406 1.104,0.604 0.552,0.198 10 false CANH*b 0.594,1.833 1.115,2.031 0.521,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to No. 2 Junction Connector


Disconnect the No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F82-4 (CANH) - F82-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 junction connector




OK

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the F82 No. 1 junction connector.


b.
U160866C03
2.083,1.365 2.427,0.521 true 2.083,1.573 2.417,1.948 true 0.104,0.094 0.333,0.323 0.229,0.229 10 false *a 0.563,1.229 0.969,1.406 0.406,0.177 10 false A61 2.458,0.385 3.042,0.615 0.583,0.229 10 false CANH*b 2.458,1.854 3.031,2.073 0.573,0.219 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to ECM


Disconnect the No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A61-9 (CANH) - A61-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM




OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - ECM)