Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 3 main lines and/or CAN branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 1 junction connector



*1: for Radio and display type

*2: for Navigation receiver type


WIRING DIAGRAM

E351561E01
1.063,0.813 1.677,1.01 0.615,0.198 10 false CA3H 1.094,1.281 1.5,1.49 0.406,0.208 10 false CA3L 3.844,0.813 4.094,1.01 0.25,0.198 10 false 9 3.792,1.281 4.042,1.479 0.25,0.198 10 false 20 3.781,4.938 4.031,5.135 0.25,0.198 10 false 11 3.781,5.427 4.031,5.625 0.25,0.198 10 false 22 1.583,0.813 1.833,1.01 0.25,0.198 10 false 6 1.583,1.292 1.833,1.49 0.25,0.198 10 false 21 1.542,4.917 1.792,5.115 0.25,0.198 10 false 19 1.563,5.417 1.813,5.615 0.25,0.198 10 false 20 1.042,4.938 1.656,5.135 0.615,0.198 10 false CAYH 1.063,5.417 1.677,5.615 0.615,0.198 10 false CAYL 0.51,5.25 1.125,5.448 0.615,0.198 10 false 120 Ω 0.5,1.156 1.115,1.354 0.615,0.198 10 false 120 Ω 0.188,5.896 0.802,6.094 0.615,0.198 10 false F139 0.177,6.052 2.167,6.5 1.99,0.448 10 false Central Gateway ECU (Network Gateway ECU) 3.76,5.844 4.375,6.042 0.615,0.198 10 false F82 3.75,6 5.5,6.25 1.75,0.25 10 false No. 1 Junction Connector 4.896,2.854 5.146,3.052 0.25,0.198 10 false 10 4.896,3.333 5.146,3.531 0.25,0.198 10 false 21 5.51,2.76 5.76,2.958 0.25,0.198 10 false 10 5.906,2.771 6.156,2.969 0.25,0.198 10 false 10 5.563,3.26 5.813,3.458 0.25,0.198 10 false 9 5.927,3.26 6.177,3.458 0.25,0.198 10 false 9 5.448,2.948 5.781,3.146 0.333,0.198 10 false F127 5.813,2.938 6.146,3.135 0.333,0.198 10 false F132 5.823,3.417 6.156,3.615 0.333,0.198 10 false F132 5.458,3.427 5.792,3.625 0.333,0.198 10 false F127 5.51,3.125 5.76,3.323 0.25,0.198 10 false *1 5.542,3.646 5.792,3.844 0.25,0.198 10 false *1 5.906,3.125 6.156,3.323 0.25,0.198 10 false *2 5.927,3.635 6.177,3.833 0.25,0.198 10 false *2 6.24,2.948 6.854,3.146 0.615,0.198 10 false CANH 6.26,3.438 6.875,3.635 0.615,0.198 10 false CANL 5.375,3.958 7.115,4.531 1.74,0.573 10 false Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2 4.302,6.479 6.635,6.729 2.333,0.25 10 false *2: for Navigation Receiver Type 1.896,6.458 4.229,6.708 2.333,0.25 10 false *1: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Remove the central gateway ECU (network gateway ECU) (See page Power Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL).


b.
U161128C02
1.135,0.969 0.844,0.583 true 2.344,1.604 1.542,1.219 true 1.708,1.604 1.417,1.219 true 0.938,1.594 1.229,1.208 true 0.146,0.063 0.323,0.229 0.177,0.167 10 false *a 0.438,0.469 0.885,0.625 0.448,0.156 10 false CA3H 1.563,0.281 1.906,0.458 0.344,0.177 10 false F135 0.688,1.604 1.135,1.76 0.448,0.156 10 false CA3L 2.198,1.604 2.646,1.76 0.448,0.156 10 false CAYH 1.542,1.625 1.99,1.781 0.448,0.156 10 false CAYL
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F139-21 (CA3L) Always 108 to 132 Ω
F139-19 (CAYH) - F139-20 (CAYL) Always 108 to 132 Ω




OK

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)

NG

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)
a.

Reinstall the central gateway ECU (network gateway ECU) (See page Power Source / Network>NETWORKING>NETWORK GATEWAY ECU>INSTALLATION).


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the No. 1 junction connector.


d.
U161126C02
2.229,1.333 2.667,1 true 2.219,1.531 2.5,1.833 true 2.115,1.323 2.583,0.667 true 2.083,1.552 2.25,1.917 true 2.333,1.521 2.667,1.667 true 2.344,1.406 2.667,1.25 true 0.365,1.313 0.719,1.49 0.354,0.177 10 false F82 2.76,0.906 3.354,1.063 0.594,0.156 10 false CANH*c 2.656,0.552 3.25,0.708 0.594,0.156 10 false CANH*b 2.729,1.604 3.323,1.76 0.594,0.156 10 false CANL*d 2.531,1.813 3.125,1.969 0.594,0.156 10 false CANL*c 1.938,1.948 2.531,2.104 0.594,0.156 10 false CANL*b 2.75,1.177 3.344,1.333 0.594,0.156 10 false CANH*d 0.073,0.083 0.583,0.292 0.51,0.208 10 false *a
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b Central Gateway ECU (Network Gateway ECU) (CA3H and CA3L Terminal)
*c to Radio and Display Receiver Assembly (for Radio and Display Type) or Navigation Receiver Assembly (for Navigation Receiver Type)
*d Central Gateway ECU (Network Gateway ECU) (CAYH and CAYL Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F82-9 (CANH) - F82-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CA3H and CA3L terminal)
F82-10 (CANH) - F82-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*1 or Navigation receiver assembly*2
F82-11 (CANH) - F82-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CAYH and CAYL terminal)


*1: for Radio and Display Type

*2: for Navigation Receiver Type


Result
Result Proceed to
OK A
NG (ECU or sensor branch line) B
NG (Central gateway ECU (network gateway ECU) main line) C



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 1 JUNCTION CONNECTOR)

3.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>TERMINALS OF ECU).


c.
U161119C01
1.417,1.125 1.063,1.75 true 1.427,1.031 2.25,1.844 true 1.51,0.313 1.865,0.49 0.354,0.177 10 false F139 0.115,0.052 0.448,0.26 0.333,0.208 10 false *a 0.927,1.76 1.594,1.979 0.667,0.219 10 false CA3L 2.063,1.865 2.729,2.083 0.667,0.219 10 false CA3H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F139-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR