Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307624 CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "Bus Check".


·

"ECM Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside ECM

·

ECM main wire or connector

·

ECM



WIRING DIAGRAM

E229246E08
5.979,0.781 6.406,0.948 0.427,0.167 10 false CANH 5.979,1.208 6.406,1.375 0.427,0.167 10 false CANL 2.688,0.667 2.896,0.833 0.208,0.167 10 false 9 2.667,1.115 2.875,1.281 0.208,0.167 10 false 20 5.677,1.021 6,1.188 0.323,0.167 10 false 26 5.677,0.583 6,0.75 0.323,0.167 10 false 13 5.635,1.208 6.042,1.375 0.406,0.167 10 false A83 5.635,0.781 6.042,0.948 0.406,0.167 10 false A83 6.229,6.167 6.563,6.479 0.333,0.313 10 false ECM 1.24,1.677 1.521,1.844 0.281,0.167 10 false A61 5.979,2.115 6.406,2.281 0.427,0.167 10 false BATT 2.74,2.135 4.031,2.469 1.292,0.333 10 false from EFI MAIN Fuse 2.698,2.677 4.031,2.99 1.333,0.313 10 false from EFI MAIN Relay 5.979,2.656 6.406,2.823 0.427,0.167 10 false +B 5.979,3.031 6.406,3.198 0.427,0.167 10 false +B2 1.24,1.833 2.844,2.156 1.604,0.323 10 false No. 1 Junction Connector 5.708,2.448 6,2.615 0.292,0.167 10 false 2 5.719,2.854 5.979,3.021 0.26,0.167 10 false 3 5.729,1.948 6.042,2.115 0.313,0.167 10 false 1 4.396,2.281 5.073,2.448 0.677,0.167 10 false EFI NO. 3 5.979,4.292 6.406,4.458 0.427,0.167 10 false ME01 5.698,4.104 6.01,4.271 0.313,0.167 10 false 59 5.646,4.292 6.052,4.458 0.406,0.167 10 false B89 5.979,4.708 6.406,4.875 0.427,0.167 10 false E01 5.698,4.531 5.979,4.708 0.281,0.177 10 false 51 5.635,4.708 6.042,4.917 0.406,0.208 10 false B89 5.979,3.438 6.406,3.604 0.427,0.167 10 false E1 5.688,3.24 6.031,3.406 0.344,0.167 10 false 16 5.646,3.438 6.052,3.604 0.406,0.167 10 false B89 5.979,3.865 6.406,4.031 0.427,0.167 10 false E02 5.698,3.677 6.01,3.844 0.313,0.167 10 false 21 5.646,3.865 6.052,4.031 0.406,0.167 10 false B89 5.979,5.177 6.406,5.344 0.427,0.167 10 false E04 5.688,4.99 5.969,5.177 0.281,0.188 10 false 52 5.646,5.177 6.01,5.365 0.365,0.188 10 false B89 5.979,5.615 6.406,5.781 0.427,0.167 10 false EC 5.688,5.427 6,5.594 0.313,0.167 10 false 50 5.615,5.615 6.021,5.781 0.406,0.167 10 false A83 5.646,1.677 6.052,1.844 0.406,0.167 10 false A83 5.979,1.667 6.406,1.833 0.427,0.167 10 false IGSW 3.083,1.667 4.052,2 0.969,0.333 10 false from IG2 Relay 5.677,1.49 5.99,1.656 0.313,0.167 10 false 37 4.604,1.833 4.875,2 0.271,0.167 10 false IG2 5.635,2.125 6.042,2.292 0.406,0.167 10 false A83 5.635,3.031 6.042,3.198 0.406,0.167 10 false A83 5.625,2.646 6.031,2.813 0.406,0.167 10 false A83

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM MAIN WIRE)
a.

Disconnect the ECM connector.


b.
E351558C01
1.75,0.333 2.25,0.583 0.5,0.25 1.781,2.74 2.865,1.656 true 2.198,0.833 2.865,1.5 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.75,0.729 2.365,0.927 0.615,0.198 10 false CANH 1.344,2.635 1.958,2.833 0.615,0.198 10 false CANL 1.885,0.365 2.5,0.563 0.615,0.198 10 false A83
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A83-13 (CANH) - A83-26 (CANL) Ignition switch off 108 to 132 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check for the ECM power source circuit (for 1NZ-FE) (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>ECM Power Source Circuit).


b.

Check for the ECM power source circuit (for 2NZ-FE) (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit).


Result
Result Proceed to
NG A
OK (for 1NZ-FE) B
OK (for 2NZ-FE) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

B

C