Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1632/81  Lost Communication with Rear Airbag Sensor RH  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly and side airbag sensor assembly RH.

The side airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

DTC No. DTC Detection Condition Trouble Area
B1632/81
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

·

Side airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Airbag sensor assembly



WIRING DIAGRAM

C241675E23
1.177,1 1.583,1.146 0.406,0.146 10 false BBR+ 1.177,1.802 1.583,1.948 0.406,0.146 10 false BBR- 5.698,1 6.104,1.146 0.406,0.146 10 false BBR+ 5.698,1.802 6.104,1.948 0.406,0.146 10 false BBR- 1.177,3.188 1.594,3.333 0.417,0.146 10 false BCR+ 1.177,3.969 1.594,4.115 0.417,0.146 10 false BCR- 3.896,3.188 4.313,3.333 0.417,0.146 10 false BCR+ 3.896,3.969 4.281,4.104 0.385,0.135 10 false BCR- 1.698,0.906 1.802,1.052 0.104,0.146 10 false 4 1.698,1.719 1.802,1.865 0.104,0.146 10 false 3 1.698,3.125 1.802,3.26 0.104,0.135 10 false 1 1.698,3.875 1.802,4.042 0.104,0.167 10 false 2 3.646,3.115 3.74,3.271 0.094,0.156 10 false 2 3.656,3.885 3.76,4.042 0.104,0.156 10 false 1 5.375,1.719 5.563,1.865 0.188,0.146 10 false 11 5.458,0.906 5.573,1.052 0.115,0.146 10 false 8 0.625,4.677 0.896,4.823 0.271,0.146 10 false K22 3.76,4.688 4.031,4.854 0.271,0.167 10 false K24 5.552,4.677 5.927,4.875 0.375,0.198 10 false K50 0.625,4.833 2.771,5.094 2.146,0.26 10 false Side Airbag Sensor Assembly RH 3.76,4.854 5.094,5.25 1.333,0.396 10 false No. 2 Side Airbag Sensor Assembly RH 5.552,4.823 7.094,5.146 1.542,0.323 10 false Airbag Sensor Assembly

PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

OK:

The connectors are properly connected


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FLOOR WIRE (OPEN)
a.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

U158362E02
6.458,1.729 6.719,1.906 true 6.344,1.729 6.063,1.948 true 3.844,1.729 3.604,1.969 true 3.958,1.729 4.25,1.958 true 1.188,0.667 1.26,1.167 false 6.271,2.365 6.406,2.104 false 0.625,1.156 0.75,1.313 0.125,0.156 10 false D 1.021,1.344 1.146,1.5 0.125,0.156 10 false C 1.354,1.344 1.479,1.5 0.125,0.156 10 false B 1.771,1.156 1.896,1.313 0.125,0.156 10 false A 0.292,1.563 0.479,1.719 0.188,0.156 10 false *1 2.75,0.427 2.948,0.583 0.198,0.156 10 false *a 5.146,0.427 5.302,0.594 0.156,0.167 10 false *b 5.24,1.094 5.406,1.24 0.167,0.146 10 false *5 5.698,1.927 6.083,2.083 0.385,0.156 10 false BCR- 6.656,1.927 7.094,2.083 0.438,0.156 10 false BCR+ 5.219,1.479 5.521,1.635 0.302,0.156 10 false K24 2.948,1.094 3.115,1.24 0.167,0.146 10 false *4 2.927,1.479 3.24,1.635 0.313,0.156 10 false K22 6.135,2.375 6.427,2.531 0.292,0.156 10 false *6 4.281,1.927 4.677,2.083 0.396,0.156 10 false BCR- 3.208,1.927 3.615,2.083 0.406,0.156 10 false BCR+ 1.01,0.583 1.198,0.74 0.188,0.156 10 false *3 1.667,1.563 1.823,1.75 0.156,0.188 10 false *2

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH *2 Side Airbag Sensor Assembly RH
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - K22-2 (BCR-) Always Below 1 Ω




OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Disconnect the service wire from connector C.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - K22-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K22-1 (BCR+) - Body ground Ignition switch ON Below 1 V
K22-2 (BCR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - Body ground Always 1 MΩ or higher
K22-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C235513E01
0.651,1.683 0.821,1.843 0.170,0.161 10 *1 1.745,1.468 1.914,1.628 0.170,0.161 10 *2

Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1632/81 is output. A
DTC B1637/82 is output. B
DTC B1632/81 or B1637/82 is not output. C

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.



A

7.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH

B

C

7.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C166174E16
1.099,1.369 1.276,1.538 0.177,0.169 10 *1 2.194,1.369 2.366,1.538 0.172,0.169 10 *2

Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1632/81 or B1637/82 is not output. A
DTC B1632/81 is output. B
DTC B1637/82 is output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH

HINT:

Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

B

C