The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.
The side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
This DTC is stored when a malfunction is detected for the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1638/82 | ·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH). ·
Side airbag sensor assembly LH malfunction ·
No. 2 side airbag sensor assembly LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire LH ·
Side airbag sensor assembly LH ·
No. 2 side airbag sensor assembly LH ·
Airbag sensor assembly |
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
| *1 | No. 2 Side Airbag Sensor Assembly LH | *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly LH) |
*b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-1 (BCL+) - K21-2 (BCL-) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-1 (BCL+) - K21-2 (BCL-) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly LH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K21-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| K21-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly LH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| K21-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly LH) |
OK
NG
Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.
Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1638/82 is output. | A |
| DTC B1633/81 is output. | B |
| DTC B1633/81 or B1638/82 is not output. | C |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.
A
B
C
Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1633/81 or B1638/82 is not output. | A |
| DTC B1638/82 is output. | B |
| DTC B1633/81 is output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
A
B
C