Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

The side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No. DTC Detection Condition Trouble Area
B1647/82
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

C241675E29
1.177,1 1.583,1.146 0.406,0.146 10 false BBL+ 1.177,1.802 1.583,1.948 0.406,0.146 10 false BBL- 5.698,1 6.104,1.146 0.406,0.146 10 false BBL+ 5.698,1.802 6.104,1.948 0.406,0.146 10 false BBL- 1.177,3.188 1.594,3.333 0.417,0.146 10 false BCL+ 1.177,3.969 1.594,4.115 0.417,0.146 10 false BCL- 3.896,3.188 4.313,3.333 0.417,0.146 10 false BCL+ 3.896,3.969 4.281,4.104 0.385,0.135 10 false BCL- 1.698,0.906 1.802,1.052 0.104,0.146 10 false 4 1.698,1.719 1.802,1.865 0.104,0.146 10 false 3 1.698,3.125 1.802,3.26 0.104,0.135 10 false 1 1.698,3.875 1.802,4.042 0.104,0.167 10 false 2 3.646,3.115 3.74,3.271 0.094,0.156 10 false 2 3.656,3.885 3.76,4.042 0.104,0.156 10 false 1 5.375,1.719 5.563,1.865 0.188,0.146 10 false 15 5.458,0.906 5.573,1.052 0.115,0.146 10 false 8 0.542,4.677 0.813,4.823 0.271,0.146 10 false K21 3.719,4.688 3.99,4.854 0.271,0.167 10 false K23 5.542,4.677 5.875,4.854 0.333,0.177 10 false K49 0.542,4.833 2.646,5.104 2.104,0.271 10 false Side Airbag Sensor Assembly LH 3.719,4.854 5.073,5.26 1.354,0.406 10 false No. 2 Side Airbag Sensor Assembly LH 5.542,4.823 7.094,5.073 1.552,0.25 10 false Airbag Sensor Assembly

PROCEDURE

1.CHECK FLOOR WIRE (OPEN)
a.

Using the service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

U158367E02
6.458,1.729 6.667,2 true 6.354,1.719 6.115,2 true 3.844,1.729 3.615,1.958 true 3.948,1.729 4.156,1.958 true 6.51,2.313 6.427,2.115 false 1.167,0.667 1.24,1.167 false 0.646,1.135 0.771,1.292 0.125,0.156 10 false D 1.031,1.323 1.156,1.479 0.125,0.156 10 false C 1.365,1.323 1.49,1.479 0.125,0.156 10 false B 1.75,1.146 1.875,1.302 0.125,0.156 10 false A 0.313,1.542 0.5,1.698 0.188,0.156 10 false *1 2.917,0.354 3.115,0.51 0.198,0.156 10 false *a 5.26,0.354 5.417,0.521 0.156,0.167 10 false *b 5.406,1.063 5.573,1.208 0.167,0.146 10 false *5 5.802,2.01 6.188,2.167 0.385,0.156 10 false BCL- 6.656,2.01 7.052,2.167 0.396,0.156 10 false BCL+ 5.365,1.448 5.656,1.604 0.292,0.156 10 false K23 3.094,1.063 3.26,1.208 0.167,0.146 10 false *4 3.063,1.448 3.375,1.604 0.313,0.156 10 false K21 6.5,2.354 6.823,2.51 0.323,0.156 10 false *6 4.177,1.948 4.573,2.104 0.396,0.156 10 false BCL- 3.25,1.948 3.656,2.104 0.406,0.156 10 false BCL+ 1,0.583 1.188,0.74 0.188,0.156 10 false *3 1.656,1.542 1.813,1.729 0.156,0.188 10 false *2

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH *2 Side Airbag Sensor Assembly LH
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - K21-2 (BCL-) Always Below 1 Ω




OK

2.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (SHORT)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Disconnect the service wire from connector C.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - K21-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

3.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K21-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K21-2 (BCL-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

4.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - Body ground Always 1 MΩ or higher
K21-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

5.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

5.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C249132E01
0.638,1.489 0.808,1.650 0.170,0.161 10 *1 1.727,1.579 1.897,1.740 0.170,0.161 10 *2

Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1647/82 is output. A
DTC B1642/81 is output. B
DTC B1642/81 or B1647/82 is not output. C

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

6.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH

B

C

6.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C166174E16
1.099,1.369 1.276,1.538 0.177,0.169 10 *1 2.194,1.369 2.366,1.538 0.172,0.169 10 *2

Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1642/81 or B1647/82 is not output. A
DTC B1647/82 is output. B
DTC B1642/81 is output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

B

C