Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1692/81  Lost Communication with Door Side Airbag Sensor RH  B1693/81  Door Side Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) is composed of the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.

The door side airbag sensor RH and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1692/81 and B1693/81 are recorded when a malfunction is detected in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH).

DTC No. DTC Detection Condition Trouble Area
B1692/81
B1693/81
When one of following conditions is met:
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) for 2 seconds.

·

Door side airbag sensor RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly



WIRING DIAGRAM

C241048E25
5.542,1.656 5.948,1.813 0.406,0.156 10 false BBR- 5.542,1.135 5.948,1.292 0.406,0.156 10 false BBR+ 5.313,1.042 5.438,1.188 0.125,0.146 10 false 8 5.25,1.552 5.438,1.698 0.188,0.146 10 false 11 1.344,2.677 1.75,2.833 0.406,0.156 10 false BDR+ 1.344,2.156 1.75,2.313 0.406,0.156 10 false BDR- 1.823,2.052 1.99,2.208 0.167,0.156 10 false 2 1.823,2.563 2,2.74 0.177,0.177 10 false 1 1.344,1.646 1.75,1.802 0.406,0.156 10 false BCR- 1.344,1.135 1.75,1.292 0.406,0.156 10 false BCR+ 1.833,1.031 1.969,1.198 0.135,0.167 10 false 4 1.823,1.542 1.979,1.698 0.156,0.156 10 false 3 3.365,2.656 3.677,2.813 0.313,0.156 10 false GK2 3.365,2.167 3.677,2.323 0.313,0.156 10 false GK2 3.479,1.969 3.667,2.115 0.188,0.146 10 false 2 3.479,2.469 3.656,2.625 0.177,0.156 10 false 1 1.354,5.042 1.76,5.198 0.406,0.156 10 false BDR- 1.354,4.51 1.76,4.667 0.406,0.156 10 false BDR+ 1.844,4.427 2.031,4.573 0.188,0.146 10 false 2 1.844,4.948 2.031,5.094 0.188,0.146 10 false 1 5.375,5.635 5.708,5.813 0.333,0.177 10 false K50 5.375,5.781 6.979,6.135 1.604,0.354 10 false Airbag Sensor Assembly 0.354,3.313 0.646,3.479 0.292,0.167 10 false K46 0.354,3.469 2.854,3.656 2.5,0.188 10 false No. 2 Side Airbag Sensor Assembly RH 0.354,5.635 0.646,5.802 0.292,0.167 10 false G16 0.365,5.781 2.479,5.979 2.115,0.198 10 false Door Side Airbag Sensor RH

PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.

OK:

The connectors are properly connected


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (OPEN)
a.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

U158398E02
1.302,0.813 1.229,0.49 false 3.646,1.354 3.854,1.094 true 4.146,1.344 3.938,1.083 true 5.99,1.375 6.354,1.073 true 6.469,1.083 6.802,1.438 true 6.333,1.469 6.375,1.354 false 1.698,0.813 1.625,0.49 false 5.5,0.938 5.781,1.115 0.281,0.177 10 false G16 0.427,1.177 0.594,1.333 0.167,0.156 10 false *1 1.979,1.167 2.146,1.323 0.167,0.156 10 false *2 1.073,0.406 1.24,0.563 0.167,0.156 10 false *3 5.604,0.146 5.771,0.302 0.167,0.156 10 false *b 3.26,0.146 3.427,0.302 0.167,0.156 10 false *a 3.188,0.948 3.448,1.125 0.26,0.177 10 false K46 5.604,0.385 5.771,0.542 0.167,0.156 10 false *6 3.26,0.385 3.427,0.542 0.167,0.156 10 false *5 1.479,0.979 1.604,1.135 0.125,0.156 10 false C 1.792,0.979 1.906,1.135 0.115,0.156 10 false B 2.083,0.792 2.198,0.948 0.115,0.156 10 false A 0.76,0.792 0.865,0.948 0.104,0.156 10 false F 5.594,1.313 5.99,1.469 0.396,0.156 10 false BDR- 6.646,1.448 7.052,1.604 0.406,0.156 10 false BDR+ 6.198,1.479 6.49,1.635 0.292,0.156 10 false *7 3.458,1.396 3.865,1.552 0.406,0.156 10 false BDR+ 3.979,1.375 4.385,1.531 0.406,0.156 10 false BDR- 1.375,0.979 1.5,1.135 0.125,0.156 10 false D 1.063,0.979 1.188,1.135 0.125,0.156 10 false E 1.448,0.406 1.615,0.563 0.167,0.156 10 false *4

Text in Illustration
*1 Door Side Airbag Sensor RH *2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector B *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - K46-2 (BDR-) Always Below 1 Ω




OK

3.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT)

NG

8.CHECK FRONT DOOR WIRE RH (OPEN)
3.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Disconnect the service wire from connector E.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - K46-2 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

4.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO B+)

NG

9.CHECK FRONT DOOR WIRE RH (SHORT)
4.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO B+)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K46-1 (BDR+) - Body ground Ignition switch ON Below 1 V
K46-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

5.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO GROUND)

NG

10.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
5.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO GROUND)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - Body ground Always 1 MΩ or higher
K46-2 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

6.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

NG

11.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
6.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C235513E01
0.651,1.683 0.821,1.843 0.170,0.161 10 *1 1.745,1.468 1.914,1.628 0.170,0.161 10 *2

Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692/81 or B1693/81 is output. A
DTC B1697/82 or B1698/82 is output. B
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.



A

7.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

7.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C166174E16
1.099,1.369 1.276,1.538 0.177,0.169 10 *1 2.194,1.369 2.366,1.538 0.172,0.169 10 *2

Interchange the door side airbag sensor RH with the door side airbag sensor LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output. A
DTC B1692/81 or B1693/81 is output. B
DTC B1697/82 or B1698/82 is output. C

Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly RH

HINT:

Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.



A

B

C

8.CHECK FRONT DOOR WIRE RH (OPEN)
a.

Disconnect the floor wire connector from the front door wire RH.

U158402E03
1.333,0.813 1.25,0.49 false 3.833,1.458 4.042,1.198 true 4.344,1.458 4.135,1.198 true 5.458,1.375 5.833,1.073 true 5.958,1.083 6.292,1.438 true 5.813,1.469 5.844,1.354 false 1.823,0.802 1.75,0.479 false 4.938,0.938 5.219,1.115 0.281,0.177 10 false G16 0.448,1.177 0.615,1.333 0.167,0.156 10 false *1 2.104,1.167 2.271,1.323 0.167,0.156 10 false *2 1.073,0.396 1.24,0.552 0.167,0.156 10 false *3 5.073,0.146 5.24,0.302 0.167,0.156 10 false *b 3.292,0.146 3.458,0.302 0.167,0.156 10 false *a 3.26,0.865 3.563,1.042 0.302,0.177 10 false GK2 5.073,0.385 5.24,0.542 0.167,0.156 10 false *6 3.292,0.385 3.458,0.542 0.167,0.156 10 false *5 1.604,0.979 1.729,1.135 0.125,0.156 10 false C 1.917,0.979 2.031,1.135 0.115,0.156 10 false B 2.208,0.792 2.323,0.948 0.115,0.156 10 false A 0.792,0.792 0.896,0.948 0.104,0.156 10 false F 5.073,1.313 5.448,1.469 0.375,0.156 10 false BDR- 6.115,1.448 6.531,1.604 0.417,0.156 10 false BDR+ 5.677,1.479 5.969,1.635 0.292,0.156 10 false *7 3.656,1.49 4.063,1.646 0.406,0.156 10 false BDR+ 4.156,1.49 4.563,1.646 0.406,0.156 10 false BDR- 1.396,0.979 1.521,1.135 0.125,0.156 10 false D 1.094,0.979 1.219,1.135 0.125,0.156 10 false E 1.563,0.385 1.729,0.542 0.167,0.156 10 false *4

Text in Illustration
*1 Door Side Airbag Sensor RH *2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector D *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to Floor Wire)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)

HINT:

The service wire has already been inserted into connector E.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - GK2-2 (BDR-) Always Below 1 Ω




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

9.CHECK FRONT DOOR WIRE RH (SHORT)
a.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - GK2-2 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

10.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
a.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the front door wire RH connector from the floor wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GK2-1 (BDR+) - Body ground Ignition switch ON Below 1 V
GK2-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

11.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
a.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Disconnect the front door wire RH connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - Body ground Always 1 MΩ or higher
GK2-2 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH