The circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH) is composed of the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.
The door side airbag sensor LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
DTC B1697/82 and B1698/82 are recorded when a malfunction is detected in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1697/82
B1698/82 |
When one of following conditions is met:
·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH) for 2 seconds. ·
Door side airbag sensor LH malfunction ·
No. 2 side airbag sensor assembly LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire LH ·
Door side airbag sensor LH ·
No. 2 side airbag sensor assembly LH ·
Airbag sensor assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.
The connectors are properly connected
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.
Check that the terminals of connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
| *1 | Door Side Airbag Sensor LH | *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH | *4 | Floor Wire |
| *5 | Connector B | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor LH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K45-1 (BDL+) - K45-2 (BDL-) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K45-1 (BDL+) - K45-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K45-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| K45-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K45-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| K45-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH) |
OK
NG
Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1697/82 or B1698/82 is output. | A |
| DTC B1692/81 or B1693/81 is output. | B |
| DTCs B1692/81, B1693/81, B1697/82 and B1698/82 are not output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
A
B
C
Interchange the door side airbag sensor LH with the door side airbag sensor RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1692/81, B1693/81, B1697/82 and B1698/82 are not output. | A |
| DTC B1697/82 or B1698/82 is output. | B |
| DTC B1692/81 or B1693/81 is output. | C |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.
A
B
C
Disconnect the floor wire connector from the front door wire LH.
| *1 | Door Side Airbag Sensor LH | *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH | *4 | Floor Wire |
| *5 | Connector D | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Floor Wire) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor LH) |
The service wire has already been inserted into connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| HK2-1 (BDL+) - HK2-2 (BDL-) | Always | Below 1 Ω |
OK
NG
Disconnect the floor wire connector from the front door wire LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| HK2-1 (BDL+) - HK2-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the front door wire LH connector from the floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| HK2-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| HK2-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Disconnect the front door wire LH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| HK2-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| HK2-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG