Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2017.01
RM19S0E _51 Engine / Hybrid System _051464 CRUISE CONTROL _0307843 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Lane Departure Alert System Circuit  


WIRING DIAGRAM

E357609E01
1.052,0.49 2.5,0.688 1.448,0.198 10 false from IG1 NO. 1 Relay 3.521,0.667 4.469,0.833 0.948,0.167 10 false ECU-IG NO. 1 5.719,0.427 5.875,0.594 0.156,0.167 10 false 7 5.677,1.323 5.906,1.5 0.229,0.177 10 false 10 5.958,0.469 6.302,0.646 0.344,0.177 10 false IG1 5.969,1.417 6.396,1.594 0.427,0.177 10 false GND 5.667,2.031 5.948,2.208 0.281,0.177 10 false L11 5.677,2.208 7.01,2.563 1.333,0.354 10 false Pre-Crash Safety City Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If a pre-crash safety city sensor which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be stored.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Pre-crash Safety City Sensor Learning.




PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V



b.

Using the parts location and system diagram, check the system for blown-out fuses, open or short circuits in the wire harness(es) and connectors that are not properly connected by performing a visual check.

HINT:

If the voltage is 11 V or less, replace or recharge the battery before proceeding to the next step.




NEXT

2.CHECK PRE-CRASH SAFETY CITY SENSOR
2.CHECK PRE-CRASH SAFETY CITY SENSOR
a.

Check pre-crash safety city sensor.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, make sure to clear the DTCs using the GTS once the inspection has been completed.


i.
U161326E04
1.021,1.844 1.302,1.427 true 1.802,1.427 2.188,1.813 true 0.156,0.125 0.5,0.365 0.344,0.24 10 false *a 1.646,0.26 1.99,0.5 0.344,0.24 10 false L11 2.094,1.833 2.479,2.021 0.385,0.188 10 false GND 0.865,1.854 1.208,2.042 0.344,0.188 10 false IG1

Disconnect the pre-crash safety city sensor connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L11-7 (IG1) - Body ground Ignition switch ON 11 to 14 V
L11-7 (IG1) - Body ground Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L11-10 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Pre-crash Safety City Sensor)




OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.


Result
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B