Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2017.01
RM19S0E _51 Engine / Hybrid System _051464 CRUISE CONTROL _0307843 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Lane Departure Alert System Switch Circuit  


DESCRIPTION

The lane departure alert system and LDA indicator (green) in the combination meter assembly turn on or off when the lane departure alert switch is pressed.

WIRING DIAGRAM

C360663E02
5.531,1.01 6.146,1.208 0.615,0.198 10 false LDSW 2.677,1.01 3.292,1.208 0.615,0.198 10 false GND 3.563,1.01 4.177,1.208 0.615,0.198 10 false ECU 2.125,1.469 2.74,1.667 0.615,0.198 10 false X1 2.115,1.625 4.688,1.99 2.573,0.365 10 false Lane Departure Alert Switch (Combination Switch Assembly) 2.51,0.906 2.802,1.177 0.292,0.271 10 false 2 3.948,0.906 4.24,1.177 0.292,0.271 10 false 5 5.344,0.917 5.635,1.188 0.292,0.271 10 false 3 5.094,2.177 7,2.427 1.906,0.25 10 false Pre-Crash Safety City Sensor 5.094,2.031 5.708,2.229 0.615,0.198 10 false L11

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If a pre-crash safety city sensor which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be stored.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Pre-crash Safety City Sensor Learning.




PROCEDURE

1.INSPECT LANE DEPARTURE ALERT SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Remove the lane departure alert switch (combination switch assembly).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SWITCH>REMOVAL


b.

Inspect the lane departure alert switch (combination switch assembly).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SWITCH>INSPECTION



OK

2.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT SWITCH - PRE-CRASH SAFETY CITY SENSOR)

NG

REPLACE LANE DEPARTURE ALERT SWITCH (COMBINATION SWITCH ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT SWITCH - PRE-CRASH SAFETY CITY SENSOR)
a.

Disconnect the X1 lane departure alert switch (combination switch assembly) connector.


b.

Disconnect the L11 pre-crash safety city sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
X1-5 (ECU) - L11-3 (LDSW) Always Below 1 Ω
X1-5 (ECU) or L11-3 (LDSW) - Body ground Always 100 kΩ or higher
X1-2 (GND) - Body ground Always Below 1 Ω



OK

3.CHECK LANE DEPARTURE ALERT SYSTEM (LDA INDICATOR LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK LANE DEPARTURE ALERT SYSTEM (LDA INDICATOR LIGHT)
a.

Check that the LDA indicator light illuminates on the combination meter assembly when the lane departure alert system is turned on using the lane departure alert main switch.


Result
Result Proceed to
The LDA indicator light does not illuminate on the combination meter assembly when the lane departure alert system is turned on using the lane departure alert main switch A
The LDA indicator light illuminates on the combination meter assembly when the lane departure alert system is turned on using the lane departure alert main switch B


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B