The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1437 | When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more. | ·
CAN communication system (Skid control ECU to ECM) ·
Skid control ECU (Brake actuator assembly) |
When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | EFI communication open detection/Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
OK
NG
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output.
w/o Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM
w/ Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output | B |
| CAN communication system DTC is output (w/o Toyota Safety Sense) | C |
| CAN communication system DTC is output (w/ Toyota Safety Sense) | D |
A
B
C
D
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (brake actuator assembly) and the ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CHECK FOR INTERMITTENT PROBLEMS).
Check that there is no momentary interruption.
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output.
w/o Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM
w/ Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output | B |
| CAN communication system DTC is output (w/o Toyota Safety Sense) | C |
| CAN communication system DTC is output (w/ Toyota Safety Sense) | D |
A
B
C
D