Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC OFF indicator light will come on.

If VSC and traction control turns OFF, the TRC OFF indicator and VSC OFF indicator light will come on.

The TRC OFF indicator light is illuminated when the TRC control is prohibited by operating the VSC OFF switch.

By Pressing the VSC OFF switch for a short time, the TRC OFF mode is activated, and the TRC control is prohibited, and the TRC OFF indicator light in the combination meter is illuminated.

By pressing the VSC OFF switch for 3 seconds or longer, the VSC OFF mode is activated, the VSC and TRC controls are prohibited, and both the VSC OFF indicator light and the TRC OFF indicator light are illuminated.

WIRING DIAGRAM

C243296E08
0.594,0.583 0.917,0.74 0.323,0.156 10 false CPU 1.531,0.448 2.052,0.594 0.521,0.146 10 false CAN I/F 0.813,1.625 1.469,1.771 0.656,0.146 10 false TRC OFF 1.531,2.219 1.729,2.375 0.198,0.156 10 false IG 0.375,2.51 2.219,2.667 1.844,0.156 10 false Combination Meter Assembly 2.958,1.771 3.229,1.927 0.271,0.156 10 false F57 2.969,1.917 4.063,2.063 1.094,0.146 10 false VSC OFF Switch 3.021,1.365 3.115,1.521 0.094,0.156 10 false 3 3.99,1.365 4.083,1.521 0.094,0.156 10 false 6 5.146,1.344 5.333,1.5 0.188,0.156 10 false 30 5.417,1.448 5.781,1.604 0.365,0.156 10 false CSW 5.219,2.01 5.49,2.156 0.271,0.146 10 false A54 5.219,2.177 6.781,2.552 1.563,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 0.646,3.208 2.375,3.365 1.729,0.156 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result
Result Proceed to
DTC is not output A
DTC is output (w/o Toyota Safety Sense) B
DTC is output (w/ Toyota Safety Sense) C


A

3.INSPECT BATTERY

B

C

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

B

C

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.
U158457E01
0.044,0.021 0.243,0.183 0.199,0.162 10 *a 1.589,0.159 1.872,0.307 0.284,0.149 10 A54 1.51,1.882 1.889,2.030 0.379,0.149 10 CSW 1.795,1.385 1.722,1.854 false

Disconnect the skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A54-30 (CSW) - Body ground VSC OFF Switch held on Below 1 Ω
A54-30 (CSW) - Body ground VSC OFF Switch off (Not pressed) 10 kΩ or higher



Text in Illustration
*a Front view of wire harness connector
(to skid control ECU)

d.

Reconnect the skid control ECU connector.



OK

5.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

8.INSPECT VSC OFF SWITCH
5.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode/Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode TRC OFF: TRC OFF mode
Unknown: Unspecified
VSC OFF: TRC, VSC OFF mode
-


g.

Check that the mode display changes according to the VSC OFF switch operation.

OK:

Display changes according to the switch operation.




OK

6.REPLACE COMBINATION METER ASSEMBLY

NG

6.REPLACE COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



NEXT

7.CHECK COMBINATION METER ASSEMBLY
7.CHECK COMBINATION METER ASSEMBLY
a.

Perform Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The VSC OFF indicator light turns on or off in accordance with the GTS.




OK

END

NG

8.INSPECT VSC OFF SWITCH


c.

Reconnect the VSC OFF switch connector.



OK

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Disconnect the A54 skid control ECU (brake actuator assembly) connector and the F57 VSC OFF switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-30 (CSW) - F57-6 Always Below 1 Ω
F57-3 - Body ground Always Below 1 Ω
A54-30 (CSW) - Body ground Always 10 kΩ or higher



c.

Reconnect the skid control ECU (brake actuator assembly) connector and the VSC OFF switch connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR