Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2017.01
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248394 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B360751C03
0.688,0.083 1,0.24 0.313,0.156 10 false *a 2.5,0.083 2.813,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67005 1.INSPECT BACK DOOR

a.

Check that the clearance measurements of areas "A" to "L" are within the standard ranges.

B460883N02
1.427,0.24 1.74,0.438 0.313,0.198 10 false A 1.729,0.833 2.042,1.031 0.313,0.198 10 false B 2.656,0.229 2.969,0.427 0.313,0.198 10 false C 2.958,0.854 3.271,1.052 0.313,0.198 10 false D 4,0.271 4.313,0.469 0.313,0.198 10 false E 4.146,0.833 4.458,1.031 0.313,0.198 10 false F 5.458,0.615 5.771,0.813 0.313,0.198 10 false G 6.135,1.604 6.448,1.802 0.313,0.198 10 false H 5.792,2.354 6.104,2.552 0.313,0.198 10 false I 5.021,3.833 5.333,4.031 0.313,0.198 10 false J 3.833,4.104 4.146,4.302 0.313,0.198 10 false K 2.333,4.104 2.646,4.302 0.313,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 6.0 to 9.0 mm (0.236 to 0.354 in.) B -0.5 to 2.5 mm (-0.020 to 0.098 in.)
C 6.0 to 9.0 mm (0.236 to 0.354 in.) D -0.5 to 2.5 mm (-0.020 to 0.098 in.)
E 6.0 to 9.0 mm (0.236 to 0.354 in.) F -0.2 to 2.8 mm (-0.008 to 0.110 in.)
G 3.0 to 8.0 mm (0.118 to 0.315 in.) H 5.0 to 9.0 mm (0.197 to 0.354 in.)
I 4.0 to 9.0 mm (0.157 to 0.354 in.) J 4.4 to 8.4 mm (0.173 to 0.331 in.)
K 3.8 to 7.8 mm (0.150 to 0.307 in.) L 3.8 to 7.8 mm (0.150 to 0.307 in.)



Hide 58387B 4.REMOVE REAR FLOOR FINISH PLATE

Hide 5.ADJUST BACK DOOR

a.
B271651

Adjust the door position.

i.

Horizontally and vertically adjust the door by loosening the door side hinge bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



b.
B271652

Adjust the striker position.

i.

Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.


ii.

Using a "TORX" socket wrench T40, tighten the striker mounting bolts after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)