Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for 5 Door) › 2017.01–2018.06
RM19S0E _58 Vehicle Interior _051500 INTERIOR PANELS / TRIM _0248378 ROOF HEADLINING(for 5 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 5 Door)  REMOVAL  


PROCEDURE

Hide 58410B 1.REMOVE DECK BOARD ASSEMBLY

a.
B272608

Remove the deck board.


Hide 64771G 2.REMOVE SPARE WHEEL COVER

a.
B272609

Remove the spare wheel cover.


Hide 3.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 4.REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 5.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 67913 6.REMOVE FRONT DOOR SCUFF PLATE RH

a.
B376688

Disengage the 8 claws and remove the front door scuff plate.


Hide 67914 7.REMOVE FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62111C 8.REMOVE COWL SIDE TRIM BOARD RH

a.
B284314

Remove the clip.


b.

Disengage the clip to remove the cowl side trim board RH.


Hide 62112 9.REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.


Hide 62311B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B370246

Remove the front door opening trim weatherstrip RH.


Hide 62312B 11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

a.
B272618

Disengage the 5 claws and guide to remove the rear door scuff plate RH.


Hide 67918A 13.REMOVE REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62331A 14.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B370247

Remove the rear door opening trim weatherstrip RH.


Hide 62332A 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 73210 16.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH

a.
B272620

Disengage the 2 claws to remove the anchor cover.


b.
B272621

Remove the bolt to separate the front seat outer belt assembly RH.


Hide 73220 17.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62413A 18.REMOVE CENTER PILLAR LOWER GARNISH RH

a.
B272622

Disengage the 2 clips and the 2 claws.


b.

Disengage the 2 guides to remove the center pillar lower garnish RH.


Hide 62414A 19.REMOVE CENTER PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62411B 20.REMOVE CENTER PILLAR UPPER GARNISH RH

a.
B272623

Remove the 2 screws.


b.

Disengage the clip.


c.

Pass the front seat outer belt through the slit in the center pillar upper garnish RH to remove the center pillar upper garnish RH.


Hide 62412B 21.REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62211 22.REMOVE FRONT PILLAR GARNISH RH

a.
B272615E01
2.78,0.797 2.949,0.958 0.170,0.161 10 *1 2.755,0.895 2.579,0.518 false

Disengage the front pillar garnish clip and the clip.

Text in Illustration
*1 Front Pillar Garnish Clip

HINT:

The front pillar garnish clip should remain between the front pillar garnish RH and pillar.



b.
B272616E01
1.976,0.928 2.146,1.088 0.170,0.161 10 *a 2.165,1.022 2.362,0.751 false

Using needle nose pliers, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.

Text in Illustration
*a Protective Tape

NOTICE:
·

As a pillar garnish clip is reusable, do not remove it from the pillar as long as it is not damaged.

·

Replace the front pillar garnish clips with new ones if they are removed from the vehicle.



HINT:

Tape the needle-nosed pliers tip before use.



c.

Disengage the 2 guides to remove the front pillar garnish RH.


d.

for 6 speakers:

i.

Disconnect the connector.



e.
B284322E06
0.51,0.427 0.646,0.333 false 0.365,0.875 0.5,0.802 false 1.167,1.313 1.333,1.271 false 1.396,2.552 1.115,2.104 false 2.25,1.906 2.073,1.625 false 2.854,1.396 2.646,1.031 false 0.75,0.938 0.646,1.146 false 0.333,0.427 0.521,0.583 0.188,0.156 10 false *a 0.188,0.792 0.375,0.948 0.188,0.156 10 false *b 0.75,0.844 0.938,1 0.188,0.156 10 false *1 1.344,1.156 1.531,1.313 0.188,0.156 10 false *a 2.24,1.906 2.438,2.083 0.198,0.177 10 true *a 2.813,1.396 3,1.552 0.188,0.156 10 true *1 1.375,2.552 1.594,2.719 0.219,0.167 10 true *b

Protect the curtain shield airbag assembly.

Text in Illustration
*1 Curtain Shield Airbag Assembly
*a Adhesive Tape
*b Protective Cover

i.

Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 62212 23.REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 09113 25.REMOVE JACK HANDLE

Hide 58387B 26.REMOVE REAR FLOOR FINISH PLATE

a.
B272624

Disengage the 4 claws and 4 guides to remove the rear floor finish plate.


Hide 73360 27.SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

a.
B272625

Remove the bolt.


b.

Disengage the 2 claws to separate the rear seat 3 point type outer belt assembly RH.


Hide 73370 28.SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 64730B 29.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

a.
B272626

Remove the 3 screws.


b.

Disengage the 4 claws and the guide.


c.

Disengage the 3 clips to remove the deck trim side panel assembly RH.


Hide 64740C 30.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62471A 31.REMOVE ROOF SIDE INNER GARNISH RH

a.
B272627

Disengage the 4 clips.


b.

Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish to remove the roof side inner garnish RH.


Hide 62472A 32.REMOVE ROOF SIDE INNER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 74310 33.REMOVE VISOR ASSEMBLY RH

a.
B272628

Remove the visor shaft from the visor holder.


b.

Remove the 2 screws and visor assembly RH.


Hide 74320 34.REMOVE VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 74348 35.REMOVE VISOR HOLDER

a.
B151362E04
1.109,0.296 1.355,0.443 0.246,0.147 10 45°

Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.

HINT:

Use the same procedure for the LH side and RH side.



Hide 74610S 36.REMOVE ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure to remove all assist grips.


a.
B175478

Using a moulding remover A, disengage the 4 claws to remove the 2 assist grip covers.


b.
B175479

Disengage the 2 clips to remove the assist grip assembly.


Hide 81260A 37.REMOVE MAP LIGHT ASSEMBLY

Hide 81240 38.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 88184 39.REMOVE PRE-CRASH SAFETY CITY COVER 2ND (w/ Pre-crash Safety System)

Hide 88183 40.REMOVE PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)

Hide 73350C 41.SEPARATE REAR CENTER SEAT OUTER BELT ASSEMBLY

a.
B284328

Disengage the 2 claws and open the slip joint cover.


b.
B284329

Remove the bolt to separate the rear center seat outer belt assembly.


Hide 42.REMOVE ROOF HEADLINING ASSEMBLY

B420345C02
2.302,2.781 2.552,2.781 false 4.583,2.771 4.833,2.771 false 5.979,0.25 6.667,0.75 true 6.042,0.896 6.667,0.75 true 6.083,1.24 6.677,0.76 true 5.125,5.24 6.365,5.469 true 5.302,5.115 6.375,5.469 true 5.615,4.979 6.365,5.458 true 6.313,4.677 6.365,5.458 true 0.813,4.552 0.625,5.24 true 1.229,4.802 0.615,5.24 true 1.448,4.948 0.625,5.24 true 1.594,5.135 0.625,5.229 true 4.833,4.292 5.073,4.458 0.24,0.167 10 true *a 0.219,4.292 0.438,4.458 0.219,0.167 10 true *b 4.854,0.167 5.167,0.323 0.313,0.156 10 false *c 2.938,4.625 3.25,4.833 0.313,0.208 12 true *A 2.063,2.708 2.375,2.865 0.313,0.156 10 true *e 6.76,0.708 6.99,0.885 0.229,0.177 10 false *d 4.917,2.708 5.229,2.865 0.313,0.156 10 false *e 6.396,5.51 6.625,5.688 0.229,0.177 10 false *d 0.479,5.281 0.708,5.458 0.229,0.177 10 false *d
*A w/ Pre-crash Safety System - -
*a Front Pillar RH Side *b Front Pillar LH Side
*c Rear Pillar RH Side *d Clump
*e Hook - -


a.

for front pillar RH side:

i.

Disconnect the connector.


ii.

Using a clip remover, disengage the 4 clamps.



b.

for front pillar LH side:

i.

Disconnect the connector.


ii.

Using a clip remover, disengage the 4 clamps.



c.

for rear pillar RH side:

i.

Disconnect the 2 connectors.


ii.

Using a clip remover, disengage the 3 clamps.



d.

w/ pre-crash safety system:

i.

Disconnect the connector.



e.

Disengage the 2 claws.


f.

Using a clip remover, remove the clip.


g.

Disengage the 2 hooks.


h.
B378995

Remove the roof headlining from the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or body interior.