When replacing the windshield glass of a vehicle equipped with a pre-crash safety city sensor, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the pre-crash safety city sensor may not be able to be installed due to a missing bracket or the pre-crash safety system may not operate properly due to a difference in the transmissivity of the windshield glass or the shape of the black ceramic border.
56111
1.CLEAN WINDSHIELD GLASS
Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer edge of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the application area of the No. 2 windshield glass stoppers with Primer G.
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Install 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Ceramic Notch |
| Area | Dimension |
|---|---|
| a | 7.6 mm (0.299 in.) |
| b | 40.0 mm (1.575 in.) |
Only 2-piece type No. 2 windshield glass stoppers are supplied. Use the 2-piece type windshield glass stoppers even if a 1-piece type was used.
56115A
3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
| *1 | No. 1 Windshield Glass Stopper |
Install 2 new No. 1 windshield glass stoppers to the vehicle body, as shown in the illustration.
Only 2-piece type No. 1 stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.
56117A
4.INSTALL WINDOW GLASS ADHESIVE DAM
Using a brush or sponge, coat the application area of adhesive dam with Primer G.
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Install a new adhesive dam onto the windshield glass, as shown in the illustration.
| *a | Back Side of Windshield Glass | - | - |
| Area | Dimension |
|---|---|
| a | 9.6 mm (0.378 in.) |
| b | 42.2 mm (1.661 in.) |
56111
5.INSTALL WINDSHIELD GLASS
| *a | Adhesive |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
| *a | Mark |
Position the windshield glass.
Using suction cups, place the windshield glass in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
Align the matchmarks on the windshield glass and vehicle body.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Remove the windshield glass.
| *a | Primer M |
| *b | Adhesive |
| *c | Correct |
| *d | Incorrect |
Using a brush, coat the installation surface on the vehicle body with Primer M.
Do not coat the adhesive with Primer M.
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Do not keep any of the opened Primer M for later use.
Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.
| *a | Back Side of Windshield Glass | *b | Primer G |
| Area | Dimension |
|---|---|
| a | 8.0 mm (0.315 in.) |
| b | 19.0 mm (0.748 in.) |
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
Apply Primer G onto the ceramic notches.
If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Apply adhesive to the glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
| *a | 8.0 mm (0.315 in.) |
| *b | 12.0 mm (0.472 in.) |
Cut off the tip of the cartridge nozzle, as shown in the illustration.
After cutting off the tip, use all adhesive within the time limit described in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with a cartridge.
Apply adhesive to the windshield glass, as shown in the illustration.
| *a | Back Side of Windshield Glass | *b | Adhesive |
| Area | Dimension |
|---|---|
| a | 3.0 mm (0.118 in.) |
| b | 12.0 mm (0.472 in.) |
| c | 8.0 mm (0.315 in.) |
| d | 30.5 mm (1.201 in.) |
Install the windshield glass.
| *a | Mark |
Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass.
Lightly press the front surface of the windshield glass to ensure a close fit.
Press the glass with force of 98 N (10 kgf, 22 lb) or more.
| *1 | windshield glass |
| *a | Dam |
| *b | Adhesive |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
Apply adhesive onto the windshield glass rim.
75533E
6.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, coat the application area of the moulding with Primer G.
Do not apply too much primer.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
Install a new moulding onto the windshield glass, as shown in the illustration.
| *a | Protective Tape |
Hold the windshield glass using protective tape until applied adhesive hardens.
Do not drive the vehicle within the time limits described in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
7.INSPECT FOR LEAK AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
8.INSTALL ROOF HEADLINING ASSEMBLY (for 5 Door)
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 5 Door)>INSTALLATION
Return the front section of the roof headlining assembly to the original position.
9.INSTALL ROOF HEADLINING ASSEMBLY (for 3 Door)
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION
Return the front section of the roof headlining assembly to the original position.
87810
10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
88181
11.INSTALL PRE-CRASH SAFETY CITY SENSOR (w/ Pre-crash Safety System)
12.INSTALL WINDSHIELD WIPER MOTOR AND LINK
88181
13.ADJUST PRE-CRASH SAFETY CITY SENSOR (w/ Pre-crash Safety System)
Perform adjustment using One Time Recognition or Sequential Recognition.
One Time Recognition:
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Sequential Recognition:
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)