Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › from 2017.01
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248385 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 76801 1.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 85292A 2.REMOVE REAR WIPER ARM HEAD CAP

Hide 3.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85110R 4.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 85143R 5.REMOVE REAR WIPER MOTOR GROMMET

Hide 67894B 6.REMOVE NO. 2 BACK DOOR PANEL PROTECTOR

Hide 67893A 7.REMOVE NO. 1 BACK DOOR PANEL PROTECTOR

HINT:

Use the same procedure as for the No. 2 back door panel protector.


Hide 68131 8.REMOVE BACK DOOR GLASS

a.
B467329C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the back door glass on the back door panel to prevent it from being scratched.


b.
B467330C01
1.677,1.167 2.188,1.5 2.188,1.5 1.698,1.292 true 2.24,1.438 2.458,1.656 0.219,0.219 10 true *a
*a Matchmark


Place matchmarks on the back door glass and back door panel at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the back door glass is not going to be reused.



c.

w/ Rear Window Defogger:

i.
B454775

Disconnect the 2 connectors.



d.
B454776C03
2.771,1.906 2.656,1.677 false 0.719,0.604 0.385,0.323 true 3.052,0.406 2.708,0.604 true 2.688,1.927 3,2.083 0.313,0.156 10 false *a 0.188,0.229 0.5,0.385 0.313,0.156 10 false *2 3.073,0.323 3.271,0.5 0.198,0.177 10 false *1
*1 Back Window Glass Clip RH
*2 Back Window Glass Clip LH
*a Piano Wire


Insert a piano wire at the locations shown as in the illustration.


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut the adhesive by pulling the piano wire around the back door glass.

NOTICE:
·

When separating the back door glass, take care not to damage the paint or interior and exterior ornaments.

·

When cutting the adhesive, take care not to damage the connectors on the back door glass.

·

Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.




g.
B467332

Using suction cups, disengage the back window glass clip RH and back window glass clip LH and remove the back door glass.

NOTICE:
·

To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.

·

Be careful not to drop the back door glass.

·

Leave as much adhesive on the back door panel as possible when removing the back door glass.




Hide 64813B 9.REMOVE BACK WINDOW GLASS ADHESIVE DAM

a.

When reusing the back door glass:

i.
E359122C02
0.146,0.135 0.458,0.333 0.313,0.198 10 false *a
*a Back Side of Back Door Glass


Using a scraper, remove the back window glass adhesive dam.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass adhesive dam with a new one.





Hide 75575D 10.REMOVE BACK WINDOW LOWER MOULDING

a.

When reusing the back door glass:

i.
E359123C02
0.167,0.156 0.479,0.354 0.313,0.198 10 false *a
*a Back Side of Back Door Glass


Using a scraper, remove the back window lower moulding.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window lower moulding.





Hide 64828B 11.REMOVE BACK WINDOW GLASS CLIP LH

a.

When reusing the back door glass:

i.
E359124C02
0.208,0.26 0.521,0.458 0.313,0.198 10 false *a
*a Back Side of Back Door Glass
V100155

Adhesive Tape


Apply adhesive tape to the glass at the edges of the back window glass clip as shown in the illustration to mark the installation position of the back window glass clip.

HINT:

Because the adhesive tape will be used to position the back window glass clip during installation, do not remove the adhesive tape.



ii.

Using a scraper, remove the back window glass clip LH.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass clip LH with a new one.





Hide 64827B 12.REMOVE BACK WINDOW GLASS CLIP RH

a.

When reusing the back door glass:

i.
B467326C02
0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Back Side of Back Door Glass
V100155

Adhesive Tape


Apply adhesive tape to the glass at the edges of the back window glass clip as shown in the illustration to mark the installation position of the back window glass clip.

HINT:

Because the adhesive tape will be used to position the back window glass clip during installation, do not remove the adhesive tape.



ii.

Using a scraper, remove the back window glass clip RH.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass clip RH with a new one.