Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. DTC Detection Condition Trouble Area
C1425 When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body ground) continues for 3 seconds or more.
·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

C367239E01
4.167,1.76 4.417,2.01 0.25,0.25 5.594,2.156 5.833,2.438 0.24,0.281 0.115,0.063 2.417,0.26 2.302,0.198 12 false w/ Toyota Safety Sense: 0.615,1.042 1.229,1.24 0.615,0.198 10 false STOP 1.49,2.333 1.948,2.531 0.458,0.198 10 false A92 1.479,2.479 3.469,2.719 1.99,0.24 10 false Stop Light Switch Assembly 2.365,2.979 3.74,3.229 1.375,0.25 10 false to Stop Light Circuit 1.448,0.719 1.646,0.906 0.198,0.188 10 false 7 1.677,0.875 1.833,1.073 0.156,0.198 10 false B 2.552,0.75 2.708,0.948 0.156,0.198 10 false 3 2.323,0.875 2.479,1.073 0.156,0.198 10 false L 2.542,1.365 2.698,1.563 0.156,0.198 10 false 4 1.667,2 2.125,2.198 0.458,0.198 10 false GND 1.479,1.865 1.635,2.063 0.156,0.198 10 false 2 2.146,1.469 2.604,1.667 0.458,0.198 10 false ACC 2.156,2 2.615,2.198 0.458,0.198 10 false OUT 2.542,1.885 2.698,2.083 0.156,0.198 10 false 1 5.698,0.75 6.01,0.948 0.313,0.198 10 false 22 5.979,0.865 6.594,1.063 0.615,0.198 10 false STP2 5.979,1.458 6.594,1.656 0.615,0.198 10 false STPO 5.979,1.99 6.438,2.188 0.458,0.198 10 false STP 5.698,1.344 6.01,1.542 0.313,0.198 10 false 31 5.771,1.875 5.927,2.073 0.156,0.198 10 false 2 5.781,3.219 6.24,3.417 0.458,0.198 10 false A54 5.76,3.375 7.156,4.01 1.396,0.635 10 false Skid Control ECU (Brake Actuator Assembly) 4.24,1.792 4.396,1.99 0.156,0.198 10 false A 5.667,2.219 5.823,2.417 0.156,0.198 10 false B

C367240E01
4.167,0.781 4.417,1.021 0.25,0.24 5.594,1.25 5.833,1.5 0.24,0.25 0.125,0.073 2.271,0.313 2.146,0.24 12 false w/o Toyota Safety Sense: 0.615,1.188 1.229,1.385 0.615,0.198 10 false STOP 1.469,0.906 1.625,1.104 0.156,0.198 10 false 1 1.677,1.021 1.833,1.219 0.156,0.198 10 false B 2.542,0.917 2.698,1.115 0.156,0.198 10 false 2 2.333,1.021 2.49,1.219 0.156,0.198 10 false L 1.667,1.656 2.125,1.854 0.458,0.198 10 false GND 1.469,1.531 1.625,1.729 0.156,0.198 10 false 3 1.521,1.99 1.979,2.188 0.458,0.198 10 false A91 1.51,2.156 3.583,2.438 2.073,0.281 10 false Stop Light Switch Assembly 2.333,2.646 3.854,2.875 1.521,0.229 10 false to Stop Light Circuit 5.781,0.896 5.938,1.094 0.156,0.198 10 false 2 5.979,1.031 6.438,1.229 0.458,0.198 10 false STP 5.885,3.26 6.344,3.458 0.458,0.198 10 false A54 5.875,3.427 7.135,4.01 1.26,0.583 10 false Skid Control ECU (Brake Actuator Assembly) 4.25,0.823 4.406,1.021 0.156,0.198 10 false A 5.667,1.292 5.823,1.49 0.156,0.198 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

5.INSPECT STOP LIGTH SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-


d.

Check that the stop light condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.RECONFIRM DTC

NG

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.



Result
Result Proceed to
DTC C1425 is not output A
DTC C1425 is output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

B

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C231271C05
0.167,0.969 0.573,1.229 0.406,0.26 1.604,0.979 1.844,1.906 true 0.104,0.135 0.49,0.406 0.385,0.271 10 *a 0.26,1.031 0.698,1.344 0.438,0.313 10 A54 1.771,1.948 2.198,2.156 0.427,0.208 10 STP

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-2 (STP) - Body ground Stop light switch ON
(Brake pedal depressed)
8 to 14 V
Stop light switch OFF
(Brake pedal released)
Below 1.5 V



Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU (Brake Actuator Assembly))

e.

Reconnect the skid control ECU (brake actuator assembly) connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - STOP LIGHT CIRCUIT)

5.INSPECT STOP LIGTH SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - STOP LIGHT CIRCUIT)

NG

REPLACE STOP LIGTH SWITCH ASSEMBLY