Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.01
RM19S0E _51 Engine / Hybrid System _051464 CRUISE CONTROL _0248153 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.

When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.

DTC Code DTC Detection Condition Trouble Area
P0571 The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
·

Stop light switch circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

B283124E07
0.281,0.688 1.188,0.854 0.906,0.167 10 false from IG2 Fuse 0.406,1.479 1.188,1.646 0.781,0.167 10 false from Battery 2.021,1.323 2.427,1.49 0.406,0.167 10 false STOP 3.125,0.615 3.219,0.781 0.094,0.167 10 false 4 4.031,0.615 4.125,0.781 0.094,0.167 10 false 3 3.125,1.406 3.219,1.573 0.094,0.167 10 false 2 4.031,1.406 4.125,1.573 0.094,0.167 10 false 1 2.865,1.896 3.135,2.052 0.271,0.156 10 false A38 2.865,2.052 4.833,2.281 1.969,0.229 10 false Stop Light Switch Assembly 6.135,2.167 6.479,2.313 0.344,0.146 10 false ECM 5.906,1.5 6.198,1.646 0.292,0.146 10 false STP 5.906,0.708 6.281,0.854 0.375,0.146 10 false ST1- 6.135,2 6.479,2.156 0.344,0.156 10 false A83 5.677,1.406 5.854,1.573 0.177,0.167 10 false 9 5.604,0.615 5.813,0.781 0.208,0.167 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
U127178E02
0.198,0.219 0.396,0.385 0.198,0.167 10 false *a 1.583,0.365 1.854,0.51 0.271,0.146 10 false A38

Disconnect the A38 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-2 - Body ground Always 11 to 14 V
A38-4 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A38 stop light switch assembly connector.


b.

Disconnect the A83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-3 - A83-10 (ST1-) Always Below 1 Ω
A38-1 - A83-9 (STP)
A38-3 - Body ground Always 10 kΩ or higher
A38-1 - Body ground


Result
Result Proceed to
NG A
OK (for 2NZ-FE) B
OK (for 1NZ-FE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C