Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1514  Torque Sensor Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C1514 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1514 Torque Sensor Power Supply Voltage Diagnosis Condition: IG ON
Malfunction Status: TRQV voltage is less than 4.5 V or more than 5.5 V.
·

Torque sensor (Steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again

WIRING DIAGRAM

C375648E05
0.26,3.021 2.24,3.385 1.979,0.365 10 false Torque Sensor (Steering Column Sub-assembly) 5.865,0.604 6.177,0.802 0.313,0.198 10 false 5V 5.115,0.823 5.729,1.021 0.615,0.198 10 false TRQV 4.896,0.813 5.052,1.01 0.156,0.198 10 false 8 4.885,2.229 5.042,2.427 0.156,0.198 10 false 2 5.104,2.24 5.719,2.438 0.615,0.198 10 false TRQG 4.802,3.115 7.156,3.406 2.354,0.292 10 false Power Steering ECU Assembly 4.813,2.958 5.125,3.156 0.313,0.198 10 false z6

CAUTION / NOTICE / HINT

NOTICE:
·

If the steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



PROCEDURE

1.INSPECT TORQUE SENSOR (STEERING COLUMN SUB-ASSEMBLY) (CHECK FOR SHORT)
a.

Disconnect the z6 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-8 (TRQV) - Body ground Always 10 kΩ or higher
z6-8 (TRQV) - z6-2 (TRQG) Always 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.INSPECT POWER STEERING ECU ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)

B

REPLACE STEERING COLUMN SUB-ASSEMBLY

C

REPLACE STEERING COLUMN SUB-ASSEMBLY

2.INSPECT POWER STEERING ECU ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)
a.

Start the engine.


b.
E316281C17
0.583,0.667 1.083,0.917 0.5,0.25 0.865,1.854 0.448,2.958 true 0.865,2.104 1.26,2.979 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.75,0.698 1.021,0.854 0.271,0.156 10 false z6 0.24,3 0.719,3.188 0.479,0.188 10 false TRQG 1.083,3 1.531,3.229 0.448,0.229 10 false TRQV
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z6-8 (TRQV) - z6-2 (TRQ6) Engine start 4.5 to 5.5 V


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE STEERING COLUMN SUB-ASSEMBLY

B

REPLACE STEERING COLUMN SUB-ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY

D

REPLACE POWER STEERING ECU ASSEMBLY