DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft and camshaft position sensor signals (2 trip detection logic) |
|
| Related DTCs | P0016: Camshaft timing misalignment at idling |
| Required Sensors/Components (Main) | VVT actuator |
| Required Sensors/Components (Related) | Camshaft position sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Within 1 minute |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010 (Camshaft Timing Oil Control Valve) P0016 (VVT system - Misalignment) P0102, P0103 (Mass Air Flow Meter) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) |
| Engine speed | 450 to 1000 rpm |
| One of following conditions met | - |
| VVT learning value at maximum retarded valve timing | Less than 25°CA |
| VVT learning value at maximum retarded valve timing | More than 51°CA |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0016 is output | A |
| DTC P0016 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the A/C on.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / VVT Change Angle #1.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft timing oil control valve assembly (Click here).
|
| ||||
| OK | |
| 5.INSPECT OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter.
Check that the filter is not clogged.
| *1 | Oil Control Valve Filter |
Reinstall the oil control valve filter.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
Replace the camshaft timing gear assembly (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 is output | B |
|
| ||||
| A | ||
| ||