Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)


DESCRIPTION

  1. Refer to DTC P0137 .

HINT:
  1. Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
  2. When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) Sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned to OFF.

  3. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.


    A237487E01


DTC No.
DTC Detection Condition
Trouble Area
P0037
Heated Oxygen (HO2) sensor heater current less than 0.3 A
(1 trip detection logic)
  1. Open in HO2 sensor heater circuit
  2. HO2 sensor heater (sensor 2)
  3. Integration relay (EFI relay)
  4. ECM
P0038
Heated Oxygen (HO2) sensor heater current 2 A or more
(1 trip detection logic)
  1. Short in HO2 sensor heater circuit
  2. HO2 sensor heater (sensor 2)
  3. Integration relay (EFI relay)
  4. ECM


CONFIRMATION DRIVING PATTERN


A198819E23

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0037 or P0038.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.


WIRING DIAGRAM

Refer to DTC P0031 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. When the value for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.
  3. Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2 (Click here).
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A115661E02
  1. Disconnect the D28 Heated Oxygen (HO2) sensor connector.

  1. Measure the resistance of the HO2 sensor connector.

    Standard resistance:
    Tester Connections
    Specified Conditions
    HT1B (1) - +B (2)
    11 to 16 Ω at 20°C (68°F)
    HT1B (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
A072895E03
  1. Disconnect the D28 HO2 sensor connector.

  1. Measure the voltage between the terminals of the D28 HO2 sensor connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (D28-2) - Body ground
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

  1. Reconnect the HO2 sensor connector.



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (EFI RELAY)
A107921E05
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse from the integration relay.

    2. Measure the EFI fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI fuse.

  1. Inspect the EFI relay.

    1. Measure the EFI relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - EFI RELAY)
A112604E01
  1. Disconnect the D28 HO2 sensor connector.

  1. Remove the integration relay from the engine room Relay Block (R/B).

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (D28-2) - Engine room R/B (1A-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (D28-2) or Engine room R/B (1A-4) - Body ground
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
A104950E01
  1. Disconnect the D28 HO2 sensor connector.

  1. Disconnect the C20 ECM connector.

  1. Measure the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    HT1B (D28-1) - HT1B (C20-47)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    HT1B (D28-1) or HT1B (C20-47) - Body ground
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037 AND/OR P0038)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read DTCs.


Result 
Display (DTC Output)
Proceed To
No output (No pending DTC output)
A
P0037 and/or P0038
B


B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)