DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|

| *1 | Exhaust Manifold Assembly | *2 | Air Fuel Ratio Sensor |
| *3 | Exhaust Pipe Assembly Front | *4 | Heated Oxygen Sensor |
| *5 | Exhaust Pipe Assembly Tail | *6 | TWC: Front Catalyst |
| *7 | TWC: Rear Catalyst | - | - |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect a Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Turn the Techstream on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Active Test operation with the engine in an idling condition (press the 12.5 or -12.5 button to change the fuel injection volume).
Monitor the voltage outputs of the air-fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (A/F) | 12.5% | Rich | Less than 3.1 |
| -12.5% | Lean | More than 3.4 | |
| O2S B1S2 (HO2) | 12.5% | Rich | More than 0.55 |
| -12.5% | Lean | Less than 0.4 |
| Status AFS Voltage B1S1 | Status O2S B1S2 | A/F Condition and A/F and HO2 Sensor Condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - |
| B |
| Rich | Lean/Rich | A/F sensor malfunction | - |
| |
| Lean/Rich | Lean | HO2 sensor malfunction | - |
| C |
| Lean/Rich | Rich | HO2 sensor malfunction | - |
| |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air-fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | |
| 4.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST) |
Replace the exhaust pipe assembly front (TWC: Front catalyst and rear catalyst) (Click here).
| NEXT | ||
| ||
| 5.REPLACE AIR-FUEL RATIO SENSOR (BANK 1 SENSOR 1) |
Replace the air fuel ratio sensor (bank 1 sensor 1) (Click here).
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR (BANK 1 SENSOR 2) |
Replace the heated oxygen sensor (bank 1 sensor 2) (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .
|
| ||||
| 10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace exhaust gas leak point.
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC is not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 12.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST) |
Replace the exhaust pipe assembly front (TWC: Front catalyst and rear catalyst) (Click here).
| NEXT | ||
| ||