Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Hatchback without VSC)

DTC    B1800/51    Short in Driver Side Squib Circuit

DTC    B1801/51    Open in Driver Side Squib Circuit

DTC    B1802/51    Short to GND in Driver Side Squib Circuit

DTC    B1803/51    Short to B+ in Driver Side Squib Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib circuit consists of the airbag sensor assembly, spiral cable sub-assembly and steering pad.
  2. The circuit instructs SRS to deploy when deployment conditions are met.
  3. These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1800/51
  1. The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during primary check.
  2. Driver side squib malfunction
  3. Spiral cable sub-assembly malfunction
  4. Airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib)
  4. Airbag sensor assembly
B1801/51
  1. The airbag sensor assembly receives an open circuit signal in the driver side squib circuit.
  2. Driver side squib malfunction
  3. Spiral cable sub-assembly malfunction
  4. Airbag sensor assembly malfunction
B1802/51
  1. The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit.
  2. Driver side squib malfunction
  3. Spiral cable sub-assembly malfunction
  4. Airbag sensor assembly malfunction
B1803/51
  1. The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit.
  2. Driver side squib malfunction
  3. Spiral cable sub-assembly malfunction
  4. Airbag sensor assembly malfunction

WIRING DIAGRAM


C241678E12


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the Techstream (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C165138E09
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the steering pad, spiral cable sub-assembly and airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the steering pad, spiral cable sub-assembly and airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

  1. Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.

    OK:
    The short springs are not deformed or damaged.

    Text in Illustration 
    *1
    Steering Pad
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag Sensor Assembly
    *4
    Instrument Panel Wire



NG
REPLACE WIRE HARNESS
OK


2.CHECK STEERING PAD (DRIVER SIDE SQUIB)


    C241527E03
  1. Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.

  1. Connect SST (resistance 2.1 Ω) to connector E.

    CAUTION:
    Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.

    Text in Illustration 
    *1
    Steering Pad
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag Sensor Assembly
    *4
    Connector E
    *a
    Front view of wire harness connector
    (to Steering Pad)
    *b
    Color: Orange

    HINT:
    Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector E.



NG
Go to step 3
OK

REPLACE STEERING PAD (Click here)  

3.CHECK DRIVER SIDE SQUIB CIRCUIT


    C241528E03
  1. Disconnect the instrument panel wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      W10-1 (D+) - Body ground
      Ignition switch ON
      Below 1 V
      W10-2 (D-) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - W10-2 (D-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - Body ground
      Always
      1 MΩ or higher
      W10-2 (D-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - W10-2 (D-)
      Always
      1 MΩ or higher

      Text in Illustration 
      *1
      Steering Pad
      *2
      Spiral Cable Sub-assembly
      *3
      Airbag Sensor Assembly
      *4
      Connector E
      *a
      Front view of wire harness connector
      (to Steering Pad)
      *b
      Color: Orange

  1. Restore the released activation prevention mechanism of connector B to the original condition.



NG
Go to step 5
OK


4.CHECK DTC


    C245746E01
  1. Connect the connectors to the steering pad and airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.

    Text in Illustration 
    *1
    Steering Pad
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag Sensor Assembly

    HINT:
    Codes other than DTCsB1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE


    C241529E02
  1. Disconnect the instrument panel wire from the spiral cable sub-assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      D113-1 (D+) - Body ground
      Ignition switch ON
      Below 1 V
      D113-2 (D-) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D113-1 (D+) - D113-2 (D-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D113-1 (D+) - Body ground
      Always
      1 MΩ or higher
      D113-2 (D-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D113-1 (D+) - D113-2 (D-)
      Always
      1 MΩ or higher

  1. Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration 
*1
Steering Pad
*2
Spiral Cable Sub-assembly
*3
Airbag Sensor Assembly
*4
Instrument Panel Wire
*5
Connector C
*a
Front view of wire harness connector
(to Spiral Cable Sub-assembly)


NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK SPIRAL CABLE SUB-ASSEMBLY


    C241530E03
  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      W10-1 (D+) - Body ground
      Ignition switch ON
      Below 1 V
      W10-2 (D-) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - W10-2 (D-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - Body ground
      Always
      1 MΩ or higher
      W10-2 (D-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      W10-1 (D+) - W10-2 (D-)
      Always
      1 MΩ or higher

  1. Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration 
*1
Steering Pad
*2
Spiral Cable Sub-assembly
*3
Airbag Sensor Assembly
*4
Instrument Panel Wire
*5
Connector E
*a
Front view of wire harness connector
(to Steering Pad)
*b
Color: Orange


NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)