DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1810/53 |
|
|
| B1811/53 |
| |
| B1812/53 |
| |
| B1813/53 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the steering pad, spiral cable sub-assembly and airbag sensor assembly.
Disconnect the connectors from the steering pad, spiral cable sub-assembly and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.
Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
|
| ||||
| OK | |
| 2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E (black connector).
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad) |
| *b | Color: Black |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector E.
|
| ||||
| OK | ||
| ||
| 3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Disconnect the instrument panel wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| W11-2 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| W11-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - W11-1 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| W11-1 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - W11-1 (D2-) | Always | 1 MΩ or higher |
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad) |
| *b | Color: Black |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the steering pad and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE |
![]() |
Disconnect the instrument panel wire from spiral cable sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D113-4 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| D113-3 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D113-4 (D2+) - D113-3 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D113-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| D113-3 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D113-4 (D2+) - D113-3 (D2-) | Always | 1 MΩ or higher |
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | |
| 6.CHECK SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| W11-2 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| W11-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - W11-1 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| W11-1 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W11-2 (D2+) - W11-1 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| *1 | Steering Pad |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *5 | Connector E |
| *a | Front view of wire harness connector (to Steering Pad) |
| *b | Color: Black |
|
| ||||
| OK | ||
| ||