Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is stored, check ignition coil No. 1 (No. 1 cylinder) circuit.
  3. If DTC P0352 is stored, check ignition coil No. 1 (No. 2 cylinder) circuit.
  4. If DTC P0353 is stored, check ignition coil No. 1 (No. 3 cylinder) circuit.
  5. If DTC P0354 is stored, check ignition coil No. 1 (No. 4 cylinder) circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil No. 1 and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A237485E02


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil No. 1 and ECM
  3. Ignition coil No. 1 (No. 1 to No. 4 cylinder)
  4. ECM

  1. A093278E43
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    Item
    Content
    Terminals
    CH1: IGT1, IGT2, IGT3, IGT4 - E1
    CH2: IGF1 - E1
    Equipment Settings
    2 V/DIV
    20 msec./DIV
    Conditions
    Cranking or idling

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353 or P0354.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the result shows INCOMPLETE or N/A, perform steps [A] through [B] again.


WIRING DIAGRAM


A239093E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT IGNITION COIL NO. 1 (POWER SOURCE)
A115969E84
  1. Disconnect the ignition coil No. 1 connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Condition
    Specified Conditions
    GND (C11-4) - Body ground
    Always
    Below 1 Ω
    GND (C12-4) - Body ground
    Always
    Below 1 Ω
    GND (C13-4) - Body ground
    Always
    Below 1 Ω
    GND (C14-4) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the wire harness side connector.

    Standard voltage:
    Tester Connections
    Switch Condition
    Specified Conditions
    +B (C11-1) - GND (C11-4)
    Ignition switch ON
    11 to 14 V
    +B (C12-1) - GND (C12-4)
    Ignition switch ON
    11 to 14 V
    +B (C13-1) - GND (C13-4)
    Ignition switch ON
    11 to 14 V
    +B (C14-1) - GND (C14-4)
    Ignition switch ON
    11 to 14 V

*a
Front view of wire harness connector
( to Ignition Coil No. 1)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL NO. 1 - ECM)
  1. Disconnect the ignition coil No. 1 connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Condition
    Specified Conditions
    IGF (C11-2) - IGF1 (C20-81)
    Always
    Below 1 Ω
    IGF (C12-2) - IGF1 (C20-81)
    Always
    Below 1 Ω
    IGF (C13-2) - IGF1 (C20-81)
    Always
    Below 1 Ω
    IGF (C14-2) - IGF1 (C20-81)
    Always
    Below 1 Ω
    IGT (C11-3) - IGT1 (C20-85)
    Always
    Below 1 Ω
    IGT2 (C12-3) - IGT2 (C20-84)
    Always
    Below 1 Ω
    IGT3 (C13-3) - IGT3 (C20-83)
    Always
    Below 1 Ω
    IGT4 (C14-3) - IGT4 (C20-82)
    Always
    Below 1 Ω
    IGF (C11-2) or IGF1 (C20-81) - Body ground
    Always
    10 kΩ or higher
    IGF (C12-2) or IGF1 (C20-81) - Body ground
    Always
    10 kΩ or higher
    IGF (C13-2) or IGF1 (C20-81) - Body ground
    Always
    10 kΩ or higher
    IGF (C14-2) or IGF1 (C20-81) - Body ground
    Always
    10 kΩ or higher
    IGT (C11-3) or IGT1 (C20-85) - Body ground
    Always
    10 kΩ or higher
    IGT2 (C12-3) or IGT2 (C20-84) - Body ground
    Always
    10 kΩ or higher
    IGT3 (C13-3) or IGT3 (C20-83) - Body ground
    Always
    10 kΩ or higher
    IGT4 (C14-3) or IGT4 (C20-82) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Shuffle arrangement of the ignition coils (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Check DTCs displayed on the Techstream.

    Result 
    Display (DTC Output)
    Proceed To
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL NO. 1 (Click here)
A

REPLACE ECM (Click here)