Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C1405    Open or Short in Front Speed Sensor RH Circuit

DTC    C1406    Open or Short in Front Speed Sensor LH Circuit


DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).

DTC NO.
DTC Detection Condition
Trouble Area
C1405
C1406
Either of the following is detected:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Harness or connector
  3. Brake actuator assembly (skid control ECU)

HINT:
  1. DTC C1405 is for the front speed sensor RH.
  2. DTC C1406 is for the front speed sensor LH.


WIRING DIAGRAM


C239921E03


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal after replacement (Click here).

1.READ VALUE USING TECHSTREAM (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    FL Speed Open
    FL speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  1. According to the display on the Techstream, read the Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTCs (C1405 and C1406) are not output
    A
    DTCs (C1405 and/or C1406) are output
    B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A15 brake actuator assembly (skid control ECU) connector and the A7 and/or A11 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-7 (FR+) - A7-2 (FR+)
    Always
    Below 1 Ω
    A15-6 (FR-) - A7-1 (FR-)
    Always
    Below 1 Ω
    A15-19 (FL+) - A11-2 (FL+)
    Always
    Below 1 Ω
    A15-18 (FL-) - A11-1 (FL-)
    Always
    Below 1 Ω
    A15-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    A15-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    A15-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A15-18 (FL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A15 brake actuator assembly (skid control ECU) connector and the front speed sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)


    C234065E03
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    RH:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-2 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    LH:
    Tester Connection
    Switch Condition
    Specified Condition
    A11-2 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)
    *b
    RH
    *c
    LH

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE FRONT SPEED SENSOR (Click here)