DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1782 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the rear occupant classification sensor LH.
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the rear occupant classification sensor LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Measure the voltage.
| Tester connection | Condition | Specified condition |
| U1-3 (SGD3) - Body ground | Ignition switch on | Below 1 V |
| U1-5 (SVC3) - Body ground | Ignition switch on | Below 1 V |
| U1-9 (SIG3) - Body ground | Ignition switch on | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (FOR OPEN) |
![]() |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect U3-1 (SVC3) and U3-3 (SGD3), and connect U3-2 (SIG3) and U3-3 (SGD3) of connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| U1-5 (SVC3) - U1-3 (SGD3) | Always | Below 1 Ω |
| U1-9 (SIG3) - U1-3 (SGD3) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (FOR SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| U1-5 (SVC3) - U1-3 (SGD3) | Always | 1 MΩ or higher |
| U1-9 (SIG3) - U1-3 (SGD3) | Always | 1 MΩ or higher |
| U1-5 (SVC3) - U1-9 (SIG3) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT SEAT WIRE RH (TO GROUND) |
![]() |
Measure the resistance.
| Tester connection | Condition | Specified condition |
| U1-3 (SGD3) - Body ground | Always | 1 MΩ or higher |
| U1-5 (SVC3) - Body ground | Always | 1 MΩ or higher |
| U1-9 (SIG3) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DTC |
Connect the connectors to the occupant classification ECU and the rear occupant classification sensor LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the on position.
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 10.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
Confirm that nothing is placed on the passenger seat.
Confirm that the beginning sensor reading is within the standard range.
Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
|
| ||||
| OK | |
| 11.CHECK DTC |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 12.REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD RH |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the separate type front seat cushion pad RH (Click here ).
| NEXT | |
| 13.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the on position.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 14.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
Confirm that nothing is placed on the passenger seat.
Confirm that the beginning sensor reading is within the standard range.
Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
| NEXT | ||
| ||