Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM (for Sedan)

OCCUPANT CLASSIFICATION SYSTEM (for Sedan) > Trouble in Passenger Airbag ON/OFF Indicator


DESCRIPTION

The occupant classification system detects the front passenger seat condition and then indicates whether the front passenger airbag is activated or not through the passenger airbag ON/OFF indicator illumination.
The passenger airbag ON/OFF indicator illumination changes depending on the front passenger seat condition as shown in the table below.

Front passenger seat condition
ON Indicator
OFF Indicator
Vacant
OFF
OFF
Adult is seated
ON
OFF
Child is seated
OFF
ON
Child restraint system is set
OFF
ON
Front passenger occupant classification system failure
OFF
ON

WIRING DIAGRAM


C242168E02


INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the on position, and check the SRS warning light condition.

    OK:
    The SRS warning light does not come on.



NG
Go to step 10
OK


2.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to the on position.

  1. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

    OK:

    Front passenger seat condition
    ON Indicator
    OFF Indicator
    Vacant
    OFF
    OFF
    Adult is seated
    ON
    OFF
    Child is seated
    OFF
    ON
    Child restraint system is set
    OFF
    ON
    Front passenger occupant classification system failure
    OFF
    ON



OK
END
NG


3.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to the lock position.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETE is displayed.



NG
Go to step 5
OK


4.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).



NG
Go to step 5
OK

END 

5.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch to the lock position.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque:
37 N*m{ 375 kgf*cm , 27 ft.*lbf }



NG
Go to step 8
OK


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETE is displayed.



NG
Go to step 8
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).



NG
Go to step 8
OK

END 

8.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Using the Techstream, read the Data List (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant classification ECU 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Buckle switch (Passenger side)/
      NG/Unset/Set
      NG: Passenger side seat belt is malfunctioning
      Unset: Front passenger side seat belt is unfastened
      Set: Front passenger side seat belt is fastened
      -

      OK:
      The Techstream display changed correctly according to the operation of buckle switch.



NG
Go to step 14
OK


9.CHECK CONNECTORS
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK:
    The connectors are connected.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check that the connectors are not damaged or deformed.

    OK:
    The connectors are normal.



NG
REPLACE WIRE HARNESS AND CONNECTOR
OK


10.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Turn the ignition switch to the lock position.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


11.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


12.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETE is displayed.


NEXT


13.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).


NEXT

END 

14.CHECK CONNECTORS
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH (passenger side buckle switch).

    OK:
    The connectors are connected.

  1. Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH (passenger side buckle switch).

  1. Check that the connectors are not damaged or deformed.

    OK:
    The connectors are normal.



NG
REPLACE WIRE HARNESS AND CONNECTOR
OK


15.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (PASSENGER SIDE BUCKLE SWITCH)
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


16.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETE is displayed.


NEXT


17.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).


NEXT

END