POWER WINDOW CONTROL SYSTEM (for Sedan) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch |

| 1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE) |
![]() |
Disconnect the F1 power window regulator switch assembly connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| F1-3 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the F1 power window regulator switch assembly connector.
|
| ||||
| OK | |
| 2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) |
![]() |
Remove the power window regulator switch assembly.
Measure the resistance of the switch when the switch is operated.
| Tester Connection | Switch Condition | Specified Condition |
| 3 - 4 2 - 1 | UP | Below 1 Ω |
| 5 - 4 2 - 1 | OFF | Below 1 Ω |
| 5 - 4 3 - 1 | DOWN | Below 1 Ω |
Reinstall the power window regulator switch assembly.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE)) |
Disconnect the F1 power window regulator switch assembly connector.

Disconnect the F4 power window regulator motor assembly connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| F1-1 - F4-1 | Below 1 Ω |
| F1-4 - F4-2 | Below 1 Ω |
| F1-1 or F4-1 - Body ground | 10 kΩ or higher |
| F1-4 or F4-2 - Body ground | 10 kΩ or higher |
Reconnect the F1 power window regulator switch assembly connector.
Reconnect the F4 power window regulator motor assembly connector.
|
| ||||
| OK | |
| 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) |
![]() |
Remove the power window regulator motor assembly.
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates counterclockwise |
Reinstall the power window regulator motor assembly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (PASSENGER SIDE)) |
![]() |
Disconnect the G1 power window regulator master switch assembly connector.
Disconnect the F1 power window regulator switch assembly connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| G1-16 (U) - F1-5 | Below 1 Ω |
| G1-15 (D) - F1-2 | Below 1 Ω |
| G1-16 (U) or F1-5 - Body ground | 10 kΩ or higher |
| G1-15 (D) or F1-2 - Body ground | 10 kΩ or higher |
Reconnect the G1 power window regulator master switch assembly connector.
Reconnect the F1 power window regulator switch assembly connector.
|
| ||||
| OK | |
| 6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (FRONT PASSENGER SWITCH) |
![]() |
Remove the power window regulator master switch.
Measure the resistance of the switch when the switch is operated.
| Window Lock Switch Condition | Power Window Switch Condition | Tester Connection | Specified Condition |
| OFF | UP | 1 (E) - 15 (D) 6 (B) - 16 (U) | Below 1 Ω |
| OFF | OFF | 1 (E) - 16 (U) 1 (E) - 15 (D) | Below 1 Ω |
| OFF | DOWN | 1 (E) - 16 (U) 6 (B) - 15 (D) | Below 1 Ω |
| ON | UP | 1 (E) - 15 (D) | 10 kΩ or higher |
| 6 (B) - 16 (U) | Below 1 Ω | ||
| ON | OFF | 15 (D) - 16 (U) | Below 1 Ω |
| ON | DOWN | 1 (E) - 16 (U) | 10 kΩ or higher |
| 6 (B) - 15 (D) | Below 1 Ω |
Reinstall the power window regulator master switch.
|
| ||||
| OK | ||
| ||