Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM (for Hatchback)

LIGHTING SYSTEM (for Hatchback) > Door Unlock Detection Switch Circuit


DESCRIPTION

The main body ECU detects the condition of each door unlock detection switch.

WIRING DIAGRAM


E232048E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos*1
    Front door unlock detection switch RH signal /
    LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FL Door Lock Pos*1
    Front door unlock detection switch LH signal /
    LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    RR-Door Lock Pos SW*2*3
    Rear door unlock detection switch LH and RH signal /
    OFF or ON
    OFF: Rear door LH and RH locked
    ON: Rear door LH or RH unlocked
    -
    RL-Door Lock Pos SW*2*3
    Rear door unlock detection switch LH and RH signal /
    OFF or ON
    OFF: Rear door LH and RH locked
    ON: Rear door LH or RH unlocked
    -

    1. *1: w/ Power Door Lock
    2. *2: w/ Theft Deterrent System
    3. *3: for 5 Door

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    OK
    A
    NG (Front door unlock detection switch does not operate)*1
    B
    NG (Rear door unlock detection switch does not operate)*2*3
    C
    1. *1: w/ Power Door Lock
    2. *2: w/ Theft Deterrent System
    3. *3: for 5 Door



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR LOCK ASSEMBLY
  1. Inspect the front door lock assembly (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the G23 or F23 front door lock assembly connector.

  1. Disconnect the D143 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH 
    Tester Connection
    Condition
    Specified Condition
    G23-8 (LSSR) - D143-7 (LSFL)
    Always
    Below 1 Ω
    G23-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    G23-7 (E) - Body ground
    Always
    Below 1 Ω
    RH 
    Tester Connection
    Condition
    Specified Condition
    F23-7 (LSSR) - D143-18 (LSFR)
    Always
    Below 1 Ω
    F23-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    F23-8 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (Click here)  

4.INSPECT REAR DOOR LOCK ASSEMBLY
  1. Inspect the rear door lock assembly (Click here).



NG
REPLACE REAR DOOR LOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the H12 or R3 rear door lock assembly connector.

  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH 
    Tester Connection
    Condition
    Specified Condition
    H12-6 (LSSR) - 3D-24
    Always
    Below 1 Ω
    H12-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    H12-9 (E) - Body ground
    Always
    Below 1 Ω
    RH 
    Tester Connection
    Condition
    Specified Condition
    R3-6 (LSSR) - 3D-25
    Always
    Below 1 Ω
    R3-6 (LSSR) - Body ground
    Always
    10 kΩ or higher
    R3-9 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.

  1. Remove the main body ECU from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E231942E03


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    LH 
    Tester Connection
    Condition
    Specified Condition
    3D-24 - MB-5 (LSR)
    Always
    Below 1 Ω
    RH 
    Tester Connection
    Condition
    Specified Condition
    3D-25 - MB-5 (LSR)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (Click here)