DTC P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 | Case 1
|
|

| ECM Terminal Name | CH1: Between VV1+ and NE- CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Related DTCs | P0340: Camshaft position sensor verify pulse input |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: Camshaft position sensor verify pulse input case 1 5 seconds: Camshaft position sensor verify pulse input case 2 |
| MIL Operation | 2 driving cycles: Camshaft position sensor verify pulse input case 1 Immediate: Camshaft position sensor verify pulse input case 2 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Starter | ON |
| Minimal battery voltage while starter ON | Less than 11 V |
| Engine speed | 600 rpm or more |
| Starter | OFF |
| VVT system misalignment | Not detected |
| Camshaft position sensor signal | No signal |
| Either of the following is met | 1 or 2 |
| 1. Camshaft position and crankshaft position phase | Misaligned |
| 2. Camshaft position sensor signal | No signal |
| Camshaft position sensor |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT CAMSHAFT POSITION SENSOR |
Inspect the camshaft position sensor (Click here).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C54-1 - C51-82 (VV1+) | Always | Below 1 Ω |
| C54-2 - C51-110 (NE-) | Always | Below 1 Ω |
| C54-1 or C51-82 (VV1+) - Body ground | Always | 10 kΩ or higher |
| C54-2 or C51-110 (NE-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR) |
![]() |
Check the camshaft position sensor installation.
|
| ||||
| OK | |
| 4.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.
Check that the timing marks on the camshaft timing sprocket and camshaft timing gear assembly are facing upward as shown in the illustration.
| *a | Timing Marks (at top center of each gear) |
| *b | Timing Mark (groove on crankshaft pulley) |
|
| ||||
| OK | |
| 5.CHECK CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the camshaft.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read DTCs.
| Result | Proceed to |
| DTC is not output (No pending DTCs output) | A |
| DTC P0340 is output | B |
|
| ||||
| A | ||
| ||