Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (for Sedan)

SEAT BELT WARNING SYSTEM (for Sedan) > Front Passenger Side Seat Belt Warning Light Malfunction


DESCRIPTION

When the ignition switch is ON and the front passenger seat is occupied, the center airbag sensor assembly communicates the status of the front seat inner belt assembly RH to the main body ECU using the CAN communication line. The main body ECU receives signals from the center airbag sensor assembly and transmits them to the combination meter assembly. When the seat belt is unfastened, the combination meter assembly flashes the front passenger seat belt warning light on the hazard warning signal switch assembly. When the seat belt is fastened, the combination meter assembly stops flashing the front passenger seat belt warning light on the hazard warning signal switch assembly.

WIRING DIAGRAM


C281466E02


INSPECTION PROCEDURE

CAUTION:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A


3.CHECK DTC OUTPUT (AIRBAG SYSTEM)
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT PASSENGER SIDE SEAT BELT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    OFF or ON
    -

    OK:
    The front passenger side seat belt warning light on the front passenger seat belt warning light.



NG
Go to step 5
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER SEAT BELT WARNING LIGHT - BATTERY)


    C281467E01
  1. Disconnect the D77 front passenger seat belt warning light connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D77-6 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to front passenger seat belt warning light)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT PASSENGER SEAT BELT WARNING LIGHT)
  1. Disconnect the D76 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D76-9 - D77-8 (PBEW)
    Always
    Below 1 Ω
    D76-9 or D77-8 (PBEW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE FRONT PASSENGER SEAT BELT WARNING LIGHT
  1. Replace the front passenger seat belt warning light (Click here).


NEXT


8.CHECK FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT
  1. Check the front passenger side seat belt warning light operation (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END (FRONT PASSENGER SEAT BELT WARNING LIGHT WAS DEFECTIVE)