Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Sedan)

CAN COMMUNICATION SYSTEM (for Sedan) > DIAGNOSIS SYSTEM



BUS CHECK
  1. Select "CAN Bus Check" from the "System Select" screen on the Techstream.

    HINT:
    If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).
    Display the "Communication Bus Check" screen for approximately 1 minute and check for ECUs and sensors that are not indicated on the screen.


CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle's optional settings. Check which systems (ECUs, sensors) are installed on the vehicle.

    ECU/Sensor name
    Check method
    Brake actuator (Skid control ECU)
    Vehicle with ABS
    Air conditioning amplifier
    Vehicle with air conditioning
    Power steering ECU
    Installed on all vehicles
    ECM
    Installed on all vehicles
    Center airbag sensor assembly
    Installed on all vehicles
    Combination meter ECU
    Installed on all vehicles
    Main body ECU
    Installed on all vehicles


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using a Techstream.
  2. If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).

  1. BRAKE ACTUATOR (SKID CONTROL ECU)(W /ABS)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF

  2. POWER STEERING ECU

    HINT:
    DTC communication uses the SIL Line.


    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129*
    Lost Communication with Brake System Control Module
    *: w/ ABS

  3. COMBINATION METER ASSEMBLY

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129*
    Lost Communication with Brake System Control Module
    *: w/ ABS

  4. AIR CONDITIONING AMPLIFIER

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    B1499/99
    Multiplex Communication Circuit

  5. ECM

    HINT:
    1. The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Engine" is not displayed on the "Communication Bus Check" screen on the Techstream, proceed to "ECM Communication Stop Mode." (Click here)

  6. MAIN BODY ECU

    HINT:
    1. The main body ECU is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Main Body" is not displayed on the "Communication Bus Check" screen on the Techstream, proceed to "Main Body ECU Communication Stop Mode." (Click here)

  7. CENTER AIRBAG SENSOR ASSEMBLY

    HINT:
    1. The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "SRS Airbag" is not displayed on the "Communication Bus Check" screen on the Techstream, proceed to "Center Airbag Sensor Communication Stop Mode." (Click here)


DTC COMBINATION TABLE
*1: This DTC may not be output when the CAN communication system malfunctions.
*2: Only stored while malfunction continues.
*3: w/ ABS
*1: This DTC may not be output when the CAN communication system malfunctions.
*2: w/ ABS
*3: w/ Air Conditioning

DTC
Trouble Mode
Output from
Output DTC
ECM Communication Stop Mode
Brake Actuator (Skid Control ECU) Communication Stop Mode
Brake Actuator (Skid Control ECU)
U0073*3
X
○*1, *2
Power Steering ECU
U0100
○
X
U0129*3
X
○
Combination Meter ECU
U0100
○
X
U0129*3
X
○

HINT:
  1. ○: It is necessary to check for the trouble mode.
  2. X: DTC is output possibility when open in side of CAN WIRE.


DTC
Trouble Mode
Output from
Output DTC
Power Steering ECU Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode*3
Combination Meter ECU Communication Stop Mode
Main Body ECU Communication Stop Mode
Brake Actuator (Skid Control ECU)
U0073*2
X
X
X
X
X
Power Steering ECU
U0100
○*1
X
X
X
X
U0129*2
○*1
X
X
X
X
Combination Meter ECU
U0100
X
X
X
○*1
X
U0129*2
X
X
X
○*1
X

HINT:
  1. ○: It is necessary to check for the trouble mode.
  2. X: DTC is output possibility when open in side of CAN WIRE.

  1. Perform troubleshooting according to the combination of DTCs output.

    HINT:
    1. Brake Actuator (Skid Control ECU) Communication Stop Mode: (Click here)
    2. Air Conditioning Amplifier Communication Stop Mode (Click here)
    3. Power Steering ECU Communication Stop Mode: (Click here)
    4. ECM Communication Stop Mode: (Click here)
    5. Main Body ECU Communication Stop Mode: (Click here)
    6. Combination Meter ECU Communication Stop Mode: (Click here)
    7. Center Airbag Sensor Communication Stop Mode: (Click here)