Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for Sedan)

ROOF HEADLINING (for Sedan) > INSTALLATION



1. INSTALL ROOF HEADLINING ASSEMBLY
  1. Install the roof headlining into the front door.

  1. Engage the 2 claws and 4 hooks.

  1. Install the 2 clips.

  1. Connect the antenna connector.

  1. Install the clamp.

  1. Connect the roof wire connector.

  1. Install the 2 clamps.



2. INSTALL MAP LIGHT ASSEMBLY
  1. Connect the map light connector.



    B114346
  1. Engage the 4 claws and install the map light.



3. INSTALL ROOM LIGHT ASSEMBLY


    B138433
  1. Engage the 4 claws and install the room light switch base.

  1. Install the roof wire into the claw of the room light holder.



    B114348
  1. Engage the 4 claws and install the room light holder.



    B138434
  1. Engage the 2 claws and install the cover.

    HINT:
    Use the same procedure for both sides.



    B114349
  1. Engage the 4 claws and install the room light lens.



4. INSTALL VISOR HOLDER RH


    B114350E01
  1. Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.



5. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



6. INSTALL VISOR ASSEMBLY RH
  1. Engage the 2 clips and install the visor.

  1. Install the visor shaft into the visor holder.



    B114351
  1. Engage the 4 claws and install a new visor bracket cover.



7. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



8. INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure to install all the assist grips.

  1. Engage the 2 clips and install the assist grip.



9. INSTALL ASSIST GRIP COVER

HINT:
Use the same procedure to install all the assist grip covers.



    B114352
  1. Engage the 2 claws and install the assist grip cover.



10. INSTALL INSTRUMENT PANEL BOX
  1. Insert the stopper of the instrument panel box from the cutout of the lower instrument panel.



    B176559
  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.



11. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


12. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


13. INSTALL FRONT PILLAR GARNISH RH
  1. Install the 3 clamps.

  1. Connect the antenna connector.

  1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



14. INSTALL FRONT PILLAR GARNISH LH
  1. Install the 4 clamps.

  1. Engage the 2 clips and the 2 claws and install the front pillar garnish.



15. INSTALL CENTER PILLAR UPPER GARNISH RH
  1. Engage the 2 hooks and 2 clips and install the center pillar upper garnish.



16. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.



17. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



18. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



19. INSTALL SEAT BELT ANCHOR COVER CAP

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the seat belt anchor cover cap.



20. INSTALL CENTER PILLAR LOWER GARNISH RH
  1. Engage the 2 clips and 3 claws and install the center pillar lower garnish.



21. INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.



22. INSTALL ROOF SIDE INNER GARNISH RH
  1. Engage the 4 clips and the claw and install the roof side inner garnish.



23. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



24. INSTALL REAR SEAT SIDE COVER RH
  1. Engage the 2 clips and the 4 claws and install the rear seat side cover.



25. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.



26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B134773E02
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Location Mark

    Paint Mark:
    Area
    Color
    RH side
    Green
    LH side
    Red



27. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



28. INSTALL REAR DOOR SCUFF PLATE RH
  1. Engage the 7 claws and install the rear door scuff plate.



29. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B134766E02
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Location Mark

    Paint Mark:
    Area
    Color
    RH side
    Blue
    LH side
    Pink



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



32. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the stud bolt and the claw and install the cowl side trim board.



33. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



34. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 11 claws and install the front door scuff plate.



35. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



36. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD


    B136275
  1. Install the luggage compartment trim inner pad.



37. INSTALL SPARE WHEEL COVER ASSEMBLY


    B136270
  1. Install the spare wheel cover assembly.



38. INSTALL REAR SEAT ASSEMBLY LH
(Click here)


39. INSTALL REAR SEAT ASSEMBLY RH
(Click here)


40. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)


41. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.